manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

197

Swash Detail

Swash Detail

(7) ELE PIT: elevator collective pitch mixing rate             

During back and forward elevator inputs at middle collective, check if the 
swash plate is raising or lowering during the input. 

[Setting method]

 Operate the transmitter stick in the direction you want to 

set. Touch the button lit in green to enter the setting mode and adjust the 
mixing rate. Do the same for the other side. 

Note:

 This setting can not be used when 

H4-00 swash mode

 is selected.

Setting ranges:  30 ~ 150%    Initial value: H3-120 = 50%, except H3-120 = 100%

(8) ELE AIL: elevator aileron mixing rate             

While moving the elevator back and forth at middle collective, check to 
make sure the aileron axis is staying level.

[Setting method]

 Operate the transmitter stick in the direction you want to 

set. Touch the button lit in green to enter the setting mode and adjust the 
mixing rate. Do the same for the other side.  

Note: 

This setting can not be used when 

H4-00 swash mode

 is selected.

Setting ranges:  30 ~ 150%    Initial value: H3-120 = 50%, except H3-120 = 100%

(9) ELE ELE2: elevator  2nd elevator mixing rate           

This parameter adjusts the elevator to 2nd elevator mixing rate. The rate 
can be adjusted separately for up and down directions individually.  

Note: 

This setting is only available if the 

H4-xx swash mode

 has been 

selected.

Setting ranges:  30 ~ 150%     Initial value: 100%

(10) AIL High / AIL Low: Linkage compensation aileron              

At HIGH pitch and LOW pitch check to make sure that the swash plate is 
staying level on the elevator and collective axis when using aileron inputs. 
If the swash plate is rising or falling: 

[Setting method]

 Operate the transmitter stick in the direction you want to 

set. Touch the button lit in green to enter the setting mode and adjust the 
mixing rate. Do the same for the other side.   

Note

: check all four directions: high/right; high/left; low/right; low/left

Setting ranges:  0 ~ 100%    Initial value: 0%

(11) AIL Dir: Compensation direction of the aileron           

If the above Data (+/-) correction from 0-100 is NOT in the correct compen-
sation direction, change the value from [+] or [-].

Setting:  +/-     Initial setting: +

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

HABONIM 77 Series Operating Maintenance Installation preview
77 Series
Brand: HABONIM Pages: 9
Icom IC-706MKII Manual preview
IC-706MKII
Brand: Icom Pages: 30
ICM Controls ICM330 Manual preview
ICM330
Brand: ICM Controls Pages: 2
ICM Controls ICM2909 Manual preview
ICM2909
Brand: ICM Controls Pages: 2
ray Super Remote Setting Up preview
Super Remote
Brand: ray Pages: 11
Paradox MG5050 Programming Steps preview
MG5050
Brand: Paradox Pages: 3
brel-motors DC-458 Manual preview
DC-458
Brand: brel-motors Pages: 2
V2 WES-EASY Manual preview
WES-EASY
Brand: V2 Pages: 48
Dakota Digital BIM-01-2-FTCH Manual preview
BIM-01-2-FTCH
Brand: Dakota Digital Pages: 12
oventrop 2104203 Operating Instructions Manual preview
2104203
Brand: oventrop Pages: 64
Linak CBH Advanced User Manual preview
CBH Advanced
Brand: Linak Pages: 33
Topway LMT070DICFWD-NJN User Manual preview
LMT070DICFWD-NJN
Brand: Topway Pages: 34
Mitsubishi A1SJ71E71N-B2 User Manual preview
A1SJ71E71N-B2
Brand: Mitsubishi Pages: 30
Harman Martin M2GO HD Safety And Installation Manual preview
Martin M2GO HD
Brand: Harman Pages: 20
National Instruments cRIO-9064 User Manual preview
cRIO-9064
Brand: National Instruments Pages: 26
Burkert 6213 EV Operating Instructions Manual preview
6213 EV
Brand: Burkert Pages: 21
GFI Kerio Control Box NG510 Quick Start Manual preview
Kerio Control Box NG510
Brand: GFI Pages: 4
DAY 72847 Instruction Manual preview
72847
Brand: DAY Pages: 23

Brands by name

Popular brands

Load more brands