FUTABA 01000141 Full Manual Download Page 81

Page: 81 / 225

Swash

Swash operation linkage correction function (helicopter only, except

swash type H-1).

Neutral Point

At your linkages, if the servo horn deviates from

a perpendicular position at neutral, the linkage

compensation functions in this menu may not

compensate effectively. To correct this use the

neutral point function. This will move the neutral

point of the servos to the actual perpendicular

position. However, this adjustment changes only

the axis point of the compensation functions in this

menu, and does not affect the neutral position of

other functions.

Swash AFR

Swash AFR function reduces/increases/reverses the

rate (travel) of the aileron, elevator and collective

pitch functions, by adjusting or reversing the

motion of all servos involved in that function, only

when using that function.

Mixing Rate

This compensation mixing is used to correct the

tendency of the swash-plate for each control. The

following compensation mixing is possible: PIT

to AIL, PIT to ELE, AIL to PIT, ELE to AIL, and

ELE to PIT (HR3 mode.) It adjusts the swash-

plate to operate correctly for each control using the

corresponding compensation mixing.

Linkage Compensation

This compensation mixing is used to correct the

tendency of the swash-plate for pitch control at low

pitch and high pitch.

Speed Compensation

This function is used to cancel the reaction that is

generated by the difference of the operation amount

of each servo when the swash-plate moves.

● Select [Swash] at the linkage menu and call the

setup screen shown below.

●Return to Linkage menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands