FUTABA 01000141 Full Manual Download Page 58

Page: 58 / 225

S.BUS/S.BUS2

Servo

S.BUS/S.BUS2

Servo

Procedure for changing S.BUS servo

setting

1. Select [S.Bus servo] of the System menu.

2. Wire the servo as shown in the figure above.

3. Press [Read]. The ID and current setting of

that servo are displayed.

S.Bus servo

S.BUS servo setting

● Call the following setting screen by pressing the

[S.BUS Servo] button in the System menu.

● Servo ID number

If you use multiple S.BUS servos, only the desired

servo in the group can be set by entering the ID of

that specific servo.

An S.BUS(2) servo can memorize the channel and

various settings you input. Servo setting can be

performed on the T16IZ screen by wiring the servo

as shown in the figure.

* With some S.BUS(2) servos, there are some functions which

cannot be used. If a function cannot be used, the display

screen will change. (Only the function which can be used by

a servo is displayed.)

* After reading completion, with connection of the above

figure, if a stick is moved, servo operation can be tested.

SERVO

3-way hub

or Y-harnesses

SERVO

4. When multiple servos are connected change

[INH] at the right side of the ID number on the

screen to [ACT] and enter the ID of the servo

you want to set.

5. Set each item. (Please see the next page.)
6. Press [Write]. The settings are changed.

●Return to System menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands