FUTABA 01000141 Full Manual Download Page 132

Page: 132 / 225

132

Currently selected condition name

● Mixing curve setting

(For a description of the

setting method, see the

description at the back

of this manual.)

Ailerons, flaps

and elevators rate

adjustment

Overall adjustment by

Rate A and Rate B.

Condition group/single

mode selection (Gr. /Sngl)

The ON/OFF switch of

mixing is chosen.

Activate the function by

tapping the [INH].

Camber mixing

[Corresponding model type]: Airplane/glider, 2 ailerons or more

This function adjusts the rate of camber

operation which operates the wing camber

(ailerons, camber flaps, brake flaps) in the

negative and positive directions. The aileron,

flap, and elevator rates can also be adjusted

independently by curve, and attitude changes

caused by camber operation can be corrected.

*Initial setting assigns camber operation to side lever LS.

● The up/down side rates of the aileron, flap, and

elevator servos can be adjusted by curve. When

the mixing direction is reversed by the linkage,

adjustments can be made by changing the

mixing rate polarity (+ or -).

● Mixing during flight can be turned ON/OFF by

setting a switch. (Always ON at [--] setting)

● A delay can be set for each condition. A cut

switch which can turn OFF the delay function can

be set.

● The speed of the aileron, flap, and elevator servos

can be set. (In side/Out side)

Servo speed setting

(For a description of the

setting method, see the

description at the back

of this manual.)

● Select [Camber mixing] at the model

menu and call the setup screen

shown below.

Condition delay cut

switch

Condition delay setting

●Return to Model menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands