FUTABA 01000141 Full Manual Download Page 84

Page: 84 / 225

Target time

Time ：

Alarm :

Last ten seconds

Last twenty seconds

One short

beep

Two short

beeps

Also

beep

Continue counting

with displaying a

minus (-) sign.

Timer

Timer setting

The Timer function may be set for

any desired time, i.e. engine run time,

specified times for competitions, etc.

Two independent timers are provided

for your use. The timers are stored

independently with each model, meaning

that when you switch between model

setups, the timer associated with the new

model is brought up automatically.

The timers may be set to start and stop

from the motion of any switch or stick.

You may set the ON and OFF directions

freely. Each timer has a capacity of up to

59 minutes 59 seconds.

Each timer may be set for count-down or count up operation

with a target time.

If a target time is set and the timer reaches the set time, a

buzzer sound for each count is generated.

A timer on the home screen starts and stops its countdown

directly from there when tapped. Tapping and holding the

display will reset the timer.

[Start/Stop]　→　Home screen

Timer 1

Timer 2

A Buzzer or Speech

can be chosen

Up timer/Down timer selection

1. Tap the mode button and select the type of

timer.

2. Timer time setting.

Tap the Mode minutes or seconds button.

Value input buttons appear on the screen.

Use these buttons to set the timer time.

Start/Stop/Reset switch setting

1. Tap the Start/Stop/Reset SW "--" button to

call the <Switch> screen, and then select the

switch and its ON direction.

(For a detailed description of the selection

method, see [Switch selection method] at

the back of this manual. The timer switches

can be set for each condition.)

[Inhibit] → [Type1-4]　

If it carries out like this,

a vibration function

will work.

● Select [Timer] at the linkage menu and call the setup

screen shown below.

●Return to

Linkage menu

OFF: Turning the power OFF and switching models will reset the timer.

ON: Previous timer is put into memory and will restart from where it stopped.

Elapsed: Minute-by-minute

alarm starting from 00:00
Remainder : Minute-by-

minute alarm counting down

from a designated time

Constant: The alarm

does not stop
One time: Stop the

alarm at once

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands