Emerson Rosemount 700XA, Reference Manual

Page: 288 / 294

CHKD
DRN
DATE
DATE
DATE
SCALE:
DWG NO.
SHT
REV
P/N
DE-22143 K
AS ABOVE 3 OF 7
MANCHA
11/13/07
SEE ORDER ENG
EM
05/11/09
NP 9/20/08
ITEM NO. PART NUMBER DESCRIPTION
Default/
QTY.
50 2-4-0710-144 PCA PLASTIC COVER BE-22161 1
51 2-4-4000-337 VALCO STEM 1
52 2-4-4000-335 VALCO VALVE 1
53 2-4-0710-068
BRACKET VALCO VALVE BE-22025
1
54 2-3-0710-018 PCA, ULTEM BOARD, FID 2
55 2-4-9213-003 SOCKET HD SCEW #6-32 x .5 LG 2
56 2-3-0710-013 PCA , TCD ULTEM BOARD 1
57 7A00154G01 700XA, FID & uFPD, HOSE ASSEMBLY 1
61 2-4-0710-164 WIRE, ASCO VALVE AR
62 2-4-9202-407 4-40 BH SCREW x .4375 LG. 1
63 2-4-0710-189 CLIP CONNECTOR BE-22212 1
64 2-4-9238-005 BIBRE WASHER FLAT #4 1
65 2-4-9221-160 KEPNUT #10 1
66
2-4-0710-159
ASCO SOL VALVE, NO (ASCO 833-630806)
2
67 2-4-0710-129 BRACKET, SSO, BE-22138 1
68
2-4-9321-554 1/16" TUBE FITTING 2
69 2-4-0710-145
BASE, SSO, NORMALLY OPEN BE-22162
1
70 2-4-9231-062
LCK/WASHER INT TOOTH #6 410SS
4
71 2-4-9202-606 M/S BH SS 6-32 x 3/8" LG. 6
72 2-4-9220-251 SOL MOUNTING NUT 4
73
DE-22294
PER ORDER MAC SOLENOID ASSY. DRAWING
AR
74 2-4-9500-041 METERING VALVE 2
75 2-4-0710-201 BRACKET STREAM, BE-22228 1
76 2-4-0710-160 ASCO SOL VALVES, NC (ASCO 833-630805) AR
77 2-4-0710-147 BASE SOLENOID ARV, BE22164 AR
109 2-4-9230-040 FLAT WASHER STD 18-8SS #4 1
110 2-4-9221-070 KEP NUT 4-40 SS 1
50 2-4-0700-137 EXHAUST FITTING BE21335 1
H. INSTALLATION PROCEDURE OF ULTEM TERMINATION BOARD:
K. INSTALLATION PROCEDURE OF SAMPLE SHUTOFF VALVE ASSEMBLY:
OPTIONAL & APPLICATION DEPENDENT: INSTALL METERING VALVE(S) (ITEM 74) INTO BRACKET (ITEM 67) 1.
IN AN ANGLE 35 AS SHOWN.
2. INSTALL SAMPLE SHUTOFF BLOCK (ITEM 69) TO BRACKET USING NUT (ITEM 72) POSITIONING VALVE
PATTERN DOWN WARD AS SHOWN.
3. INSTALL SOLENOID (ITEM66) USING EXISTING HARDWARE INTO THE SAMPEL SHUTOFF BLOCK (ITEM 69)
AS SHOWN.
4. INSTALL COMPLETE SUB-ASSEMLBY OF SAMPLE SHUTOFF (FROM STEPS 1-3) INTO THE BOTTOM OF ULTEM
PLATE (ITEM 7) AT THE "E" AND "F" LOCATION (OPTIONAL) USING #6-32 SCREWS (ITEM 71) AND #6
WASHERS (ITEM 70).
5. REFER TO WORK ORDER FOR SPECIFIC # OF VALVES & APPLICABLE DRAWINGS AND PROCEDURES.
DETAIL "A"
SECTION B-B
SCALE 1:2.5
SCALE 1:1
L. INSTALLATION PROCEDURE OF STREAM SWITCH ASSEMBLY:
FOR BRACKET ASSEMBLY "B" INSTALLATION : 1.
INSTALL THREE WAY SSO BLOCK (ITEM77) INTO BRACKET (ITEM75) AS SHOWN.
INSTALL NC SOLENOID (ITEM 76) TO BLOCK (ITEM71) 2.
* FOR THE REMAINING PART OF FID ASSEMBLY ,
SEE BILL OF MATERIAL 2-3-0710-077
** AS REQUIRED PER APPLICATION (ORDER).
BRACKET ASSEMBLY "A" IS USED FOR SSO.
BRACKET ASSEMBLY "B" IS USED FOR STREAMS SAMPLE.
(4)
(2)
(4)
**
28
53
55
46
32
(3)
(3)
(3)
(3)
(2)
73
TCD 2
TCD 1
56
(OPTIONAL) FID
2-3-0710-077
54
54
65
31
50
57
FOR DETAIL "C"
SEE DWG DE-22113
SCALE 1:2
OVEN ASSEMBLY
62
64
63
SEE CABLE
2-4-0710-059
56
(OPTIONAL)
OPTIONAL
OR
ULTEM TERMINATION BOARD
OPTIONAL
OR
SCALE 1:1
110
109
INSTALL (2) #10-32 STANDOFFS (ITEM 28) TO LOCATION "D" UNDER NEATH ULTEM PLATE (ITEM 7) AS SHOWN 1.
IN VIEW "A-A" (ON PAGE 2).
2. INSTALL ULTEM TERMINATION BOARD (ITEM 56 OR 54) AND SHEILD (ITEM 50) TO STANDOFF (FROM STEP 1)
USING #10-32 SCREWS (ITEM 31), #10 LOCK WASHER(ITEM 46) AND #10 FLAT WASHER (ITEM 32) AS SHOWN.
66
72
71
70
75
BRACKET
ASSEMLBY A
SCALE 1:2
76
77
BRACKET
ASSEMLBY B
STREAM 1
STREAM 2
STREAM 3
STREAM 4
75
74
66
69
72
67
(4)
(2)
(2)
OPTIONAL SEE
INSTALLATION PROCEDURE "L"