Emerson Rosemount 5900C Reference Manual Download | Manualshive

Page: 145 / 322

background image

Configure the verification pin

Prerequisites

Make sure that the position of the Verification Pin is accurately measured and the inner
diameter of the still-pipe is available.

Note

When the product surface is close to a Verification Pin, the radar echoes from the
Verification Pin and the product surface interfere. This may reduce the accuracy of the
measured distance to the Verification Pin. It is recommended that verification is not
performed if the distance between the Verification Pin and the product surface is less than
900 mm (see

LPG/LNG antenna requirements

$

%

A. Verification Pin

B. Minimum clearance 900 mm

Since hand dipping can not be performed in high pressurized tanks, Emerson Automation
Solutions/ Rosemount Tank Gauging has developed a unique method to verify level
gauging in such tanks. The method is based on measurements in a special radar wave
propagation mode against a fixed Verification Pin in order to verify the measurement.

Procedure

1. In the Rosemount

™

TankMaster WinSetup work space, select the

Logical View

tab.

2. Select the icon that represents the desired radar level gauge.

Reference Manual

Configuration

00809-0100-5901

September 2019

Rosemount 5900C Radar Level Gauge

145

«
...
143
144
145
146
147
...
»

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Reviews:

No comments

Related manuals for Rosemount 5900C

Brand: UnionSpecial Pages: 56

Brand: Omnia Pages: 8

Brand: Labnet Pages: 5

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: FEAS Pages: 72

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: Badger Meter Pages: 16

Brand: Bante Instruments Pages: 6

Brand: Cambro Pages: 6

Brand: lancer Pages: 3

Brand: lancer Pages: 12

Brand: R2 Pages: 26

Brand: Landoll Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands