Emerson Rosemount 5900C Reference Manual Download

Page: 268 / 322

A.13.3

Rosemount 5900C Radar Level Gauge with still-pipe
array antenna

Table A-9: Rosemount 5900C Radar Level Gauge with Still-Pipe Array Antenna Ordering Information

Model

Product Description

5900C

Radar Level Gauge

Performance class

±2 mm (0.08 in.) instrument accuracy

Safety certification (SIS)

(1)

Certified IEC 61508 SIL 2 capable

None. Ready for upgrade to Safety certification (SIS)

None

Redundancy

None. Single radar level gauge electronics

Tankbus: Power and communication

Bus powered 2-wire F

OUNDATION

™

Fieldbus (IEC 61158)

Hazardous location certification

ATEX Intrinsic Safety

IECEx Intrinsic Safety

FM-US Intrinsic Safety

FM-Canada Intrinsic Safety

INMETRO Intrinsic Safety (Brazil)

KC Intrinsic Safety (South Korea)

CCOE/PESO Intrinsic Safety (India)

(2)

Japan Intrinsic Safety

Technical Regulations Customs Union (EAC) Intrinsic Safety

None

Custody transfer type approval

None

Level measurement method

10 GHz FMCW radar technology

10 GHz FMCW radar technology for US installation

Housing

Standard enclosure, polyurethane-covered aluminum. IP 66/67

Cable entry/Conduit connections

- 14 NPT, female thread. (1 plug included)

Specifications and reference data

Reference Manual

September 2019

00809-0100-5901

268

Reference Manual

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands

Emerson Rosemount 5900C, Reference Manual

Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands