Emerson Rosemount 5900C Reference Manual Download

Page: 263 / 322

Table A-7: Rosemount 5900C Radar Level Gauge with Parabolic Antenna Ordering Information

(continued)

Cable entry/Conduit connections

- 14 NPT, female thread. (1 plug included)

M20 x 1.5 adapters, female thread. (2 adapters and 1 plug included)

Metal cable glands (

- 14 NPT). Minimum temperature -20 °C (-4 °F). ATEX/IECEx Exe approved.

(2 glands and 1 plug included)

eurofast

male connector (1 plug included)

minifast

male connector (1 plug included)

Antenna

Parabolic antenna

Antenna size

20 in./DN 500, Ø=440 mm (17.3 in.)

Antenna material

SST AISI 316L/EN 1.4436

Tank seal

PTFE with FEP fluoropolymer O-ring

PTFE with Kalrez

perfluoroelastomer O-ring

Tank connection

Welded installation

Clamped/threaded installation

Antenna options

None

(3)

Proof test verification reflector

Options (include with selected model number)

Safety certificate

(4)

IEC 61508 certificate and FMEDA-data (printed copy)

Calibration certificate

Calibration certificate (printed copy)

Material traceability certificate

(5)

Antenna material traceability certification per EN 10204 3.1

Overfill protection approval

(6)

TÜV/DIBt WHG approval for overfill protection

SVTI approval for overfill protection (Switzerland)

Tag plate

Engraved SST tag plate

Reference Manual

Specifications and reference data

00809-0100-5901

September 2019

Rosemount 5900C Radar Level Gauge

263

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands

Emerson Rosemount 5900C, Reference Manual

Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands