Emerson Rosemount 5900C Reference Manual Download

Page: 58 / 322

12. Ensure that the gauge is directed at an angle of 45° to the line of sight from the

center of the tank to the wall.

13. Use the marks on the Washer Ball to adjust the gauge so the antenna is inclined

roughly 1.5° towards the center of the tank.

Note

For products with high condensation, such as bitumen, the gauge should be
mounted with 0° inclination in order to achieve maximum signal strength.

A. Marks

B. Plumb line

C. Tank center

D. Incline antenna 1.5° towards tank center

14. Tighten the finger nut.

Installation

Reference Manual

September 2019

00809-0100-5901

Reference Manual

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands

Emerson Rosemount 5900C, Reference Manual

Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands