Emerson Rosemount 5900C Reference Manual Download | Manualshive

Page: 174 / 322

background image

FD_OFFSPEC_ALM

An alarm indicating that the device operates out of the specified measurement range. If
the condition is ignored, the device will eventually fail.

Maintenance required alerts

A Maintenance required alert indicates that the device or some part of the device needs
maintenance soon. If the condition is ignored, the device will eventually fail. There are five
parameters associated with Maintenance Required alerts, they are described below.

FD_MAINT_MAP

The FD_MAINT_MAP parameter contains a list of conditions indicating that the device or
some part of the device needs maintenance soon. The priority is not the same as the
MAINT_PRI parameter described below. It is hard coded within the device and is not user
configurable.

Note that maintenance alarms are not enabled by default for the Rosemount 5900C.

Below is a list of the conditions:

1. Auxiliary Device Measurement Close to Limit

FD_MAINT_MASK

The FD_MAINT_MASK parameter will mask any of the failed conditions listed in
FD_MAINT_MAP. A bit on means that the condition is masked out from alarming and
being broadcast to the host through the alarm parameter.

FD_MAINT_PRI

FD_MAINT_PRI designates the alarming priority of the FD_MAINT_ALM, see

The default is 0 and the recommended values are 3 to 7.

FD_MAINT_ACTIVE

The FD_MAINT_ACTIVE parameter displays which of the conditions is active.

FD_MAINT_ALM

An alarm indicating that the device needs maintenance soon. If the condition is ignored,
the device will eventually fail.

Function Check alerts

A Function Check alert indicates that the device is temporary non-valid due to some
activities, for example maintenance, on the device.

There are five parameters associated with Function Check alerts, they are described below.

FD_CHECK_MAP

The FD_CHECK_MAP parameter contains a list of informative conditions that do not have
a direct impact on the primary functions of the device. Below is a list of the conditions:

1. Check function

Configuration

Reference Manual

September 2019

00809-0100-5901

174

Reference Manual

«
...
172
173
174
175
176
...
»

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Reviews:

No comments

Related manuals for Rosemount 5900C

Brand: GE Pages: 43

Brand: GE Pages: 37

Brand: GE Pages: 210

Brand: GE Pages: 160

Brand: GE Pages: 146

Brand: GE Pages: 6

Brand: GE Pages: 27

Brand: GE Pages: 4

Brand: Xycom Pages: 99

Brand: Hagerman Pages: 4

Brand: hager Pages: 2

TECSHOW QUAD SPIDER 60

Brand: Ampro Pages: 9

Brand: Teac Pages: 44

Brand: Te Pari Pages: 6

Brand: Waters Pages: 4

Brand: Waterpik Pages: 2

Brand: Easylife Pages: 3

Brand: York Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands