Emerson Rosemount 5900C Reference Manual Download

Page: 89 / 322

Configure Calibration Distance using TankMaster

™

WinSetup

The cone antenna extension causes a small offset error that needs to be calibrated away by
adjusting the Calibration Distance parameter.

Procedure

1. Start the Rosemount

™

TankMaster

™

WinSetup configuration software.

2. In the WinSetup workspace, right-click on the device icon.
3. Select

Properties

and open the

Geometry

tab.

4. Enter the appropriate

Calibration Distance

•

For a 4-in. cone the calibration distance is about 2 mm for each 100 mm
extension

•

For a 6-in. cone the calibration distance is about 1 mm for each 100 mm
extension

•

For an 8-in. cone the calibration distance is 0

Reference Manual

Installation

00809-0100-5901

September 2019

Rosemount 5900C Radar Level Gauge

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands

Emerson Rosemount 5900C, Reference Manual

Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands