DTM Print CX86e User Manual Download Page 163

Page: 163 / 214

163

Problems Common to the Printer Driver and Utilities

Symptom

Cause/Solution

[Help] is not displayed.

The help function is not supported.

The [User Account Control] screen is

displayed.

The [User Account Control] screen may be displayed when start-

ing the installer or a utility. Click [Yes] or [Continue] to execute the

installer or utility as an administrator. If you click [NO], the installer

or utility is not started.

The [Program Compatibility Assistant]

screen is displayed.

If the [Program Compatibility Assistant] dialog box is displayed after

installation is complete (including when the installation is stopped

before it is complete), make sure to click [This program installed].

Machine Problems

The Machine Does Not Operate

Cause

Remedy

Reference

The power cord is not inserted prop-

erly.

Insert the power cord fully.

Turning On the Machine

This machine is not turned on.

Turn the machine on.

Turning On the Machine

Nothing Is Displayed on the Screen when the Power Is Turned On

Cause

Remedy

Reference

The power cord is disconnected.

Insert the power cord fully.

Turning On the Machine

A power failure has occurred.

Check whether power is supplied to

the outlet.

Printing Does Not Start

Cause

Remedy

Reference

An error is displayed.

Check the error messages and follow

the on-screen instructions.

List of Messages

The LAN cable/USB cable is not

inserted.

Insert the LAN cable/USB cable fully.

Using the Machine

There is a problem with the LAN

cable/USB cable.

Use another LAN cable/USB cable.

The LAN cable/USB cable does not

match the required standard.

Use a cable that conforms to the USB

2.0 standard.
Use a cable that conforms to the Ether-

net 10BASE-T/100BASE-TX standard.

Summary of Contents for CX86e






















































































































































































































Search results

Summary of Contents for CX86e

Reviews:

Related manuals for CX86e

Brands by name

Popular brands

DTM Print CX86e, User Manual

Search results

Summary of Contents for CX86e

Reviews:

Related manuals for CX86e

Brands by name

Popular brands