DTM Print CX86e User Manual Download Page 168

Page: 168 / 214

168

The „308:PAPER JAM“ error occurs when paper is not loaded

Cause

Remedy

Reference

There may have been a problem

with the position of the paper sen-

sors when sensor calibration was

executed, which caused an invalid

value to be detected.

Execute [BOOT MENU] > [SENSOR RE-

SET] on the operation panel.

BOOT MENU

Adjusting the Paper Sensors

(Sensor Calibration)

When a Power Failure Occurs

When a power failure occurs, the machine operates as follows.

Machine Status

Operation

Receiving

Reception is interrupted.

Printing

Printing is interrupted.
When the power supply recovers, start printing again.

Standby

Printing cannot be started.

If a power failure occurs while the machine is turned on, the machine does not turn on when the power supply resumes.

If you want the machine to automatically turn on when the power supply resumes after a power failure, set [BOOT

MENU] > [POWER RETURN] to [ALWAYS ON] or [LAST STATE].
Operation is not guaranteed if an uninterruptible power supply (UPS) or inverter is used. Do not use an uninterruptible

power supply (UPS) or inverter.

Moving the Machine

Turn off the machine.

For information on turning off the machine, refer to “Turning Off the Machine”.

Unplug all the cables.

Power cord
LAN cable/USB cable

Remove the loaded paper.

Lift up the machine and move it to the destination.

Summary of Contents for CX86e






















































































































































































































Search results

Summary of Contents for CX86e

Reviews:

Related manuals for CX86e

Brands by name

Popular brands

DTM Print CX86e, User Manual

Search results

Summary of Contents for CX86e

Reviews:

Related manuals for CX86e

Brands by name

Popular brands