DTM Print CX86e User Manual Download Page 148

Page: 148 / 214

148

Message

Description

PRESS OK BUTTON

INVALID DATA

Invalid data was received.

Press «OK» button to clear the error.

CHANGE IPV4 ADDRESS

IPV4 ADDRESS IS CONFLICTED

The IPv4 address is the same as another device.

Check the IPv4 address.

PAPER DETECTION ERROR

[ERRCODE]:ERROR [SUBCODE]

The paper sensor could not detect the paper correctly.

Check the position, cleanliness, and settings of the paper sensor.

The meaning of [SUBCODE] is indicated below.

0 to 6: An error has occurred in the bottom sensor.

11 to 15: An error has occurred in the top sensor.

21 to 26: An error has occurred in the translucent sensor.

CHANGE [MEDIA_SIZE] [MEDIA_TYPE]

PRESS OK BUTTON

The paper type of the paper loaded in the machine does not match

the print data. Load the correct paper to the machine. Press «OK»

button when loading of the paper is complete.

RESTART PRINT?

OK OR FEED/CUT

Press «OK» button to resume printing immediately.

Press «FEED/CUT» button to resume printing after cutting the paper

at the proscribed position.

Press «CANCEL» button to return to the standby screen without

printing.

REDUCE PRINT DATA

[ERRCODE]:MEMORY OVERFLOW

The print data is too complex. Attach extra memory or reduce the

size of the print data.

This error is automatically cleared after approximately 15 seconds.

PRESS OK BUTTON

[ERRCODE]:WIRELESS STARTUP ERROR

The wireless LAN module is not correctly connected to the machine.
Correctly connect the wireless LAN module to the machine or turn

the machine off and then on again.

Press «OK» button to clear this message.

PRESS OK BUTTON

[ERRCODE]:WIRELESS SETTINGS ARE INCOMPLETE

The wireless LAN settings are insufficient.

Press «OK» button to clear this message.

PRESS OK BUTTON

[ERRCODE]:NOT CONNECTED TO WIRELESS ACCESS

POINT

The machine is not connected to the wireless access point.

Press «OK» button to clear this message.

NETWORK CONFIG

WRITING

Network related settings are being configured.

WAIT A MOMENT

NETWORK INITIAL

Network related settings are being initialized.

DOWNLOAD MESSAGE

PROCESSING

Message data for updating is being processed.

DOWNLOAD MESSAGE

WRITING

Message data for updating is being written.

DOWNLOAD MESSAGE

SUCCESS

Writing of message data for updating succeeded. The machine then

restarts.

DOWNLOAD MESSAGE

FAILED[ERRCODE]

Writing of message data for updating failed.

PRESS OK BUTTON FOR RESTORATION

[ERRCODE]:RECEIVING DATA TIMEOUT

A timeout has occurred while receiving data.

This error is automatically cleared after approximately 15 seconds.

PLEASE TRY AGAIN

[ERRCODE]:FW UPDATE ERROR.IF NETWORK DOESN'T

WORK,PLEASE TRY FW UPDATE OVER USB

Failed to update the firmware.

Execute the firmware update again.

LOAD [MEDIA_SIZE]

490 :FEEDER EMPTY

The paper has run out. Load paper to the machine.

Summary of Contents for CX86e






















































































































































































































Search results

Summary of Contents for CX86e

Reviews:

Related manuals for CX86e

Brands by name

Popular brands

DTM Print CX86e, User Manual

Search results

Summary of Contents for CX86e

Reviews:

Related manuals for CX86e

Brands by name

Popular brands