SET Command Parameters
The next example selects a 10BASE-T network.
>>> SET ETHERNET TENBT
Return
Result:
ETHERNET = TENBT
>>>
FAST_SCSI_A
and
FAST_SCSI_B
The FAST_SCSI_A and FAST_SCSI_B console commands
initialize the SCSI controllers. The variable FAST_SCSI_A is
for bus A devices and FAST_SCSI_B is for bus B devices. When
fast SCSI devices are connected and FAST_SCSI_A/B is set to
ON, the SCSI firmware operates in fast SCSI mode. If both slow
and fast SCSI devices are connected to the same bus and the
FAST_SCSI_A/B command is ON, the firmware differentiates
between devices.
Note that the recommended maximum bus length is 4 meters
for slow SCSI devices and 3 meters for fast SCSI devices. When
these limits are exceeded, the SCSI bus is likely to have errors.
If your total bus length, including internal and external cables,
is greater than 3 meters, you must set the FAST_SCSI_A/B
command for that bus OFF.
Available
Settings
You can set FAST_SCSI_A and FAST_SCSI_B to ON or OFF.
•
ON to operate in slow and fast SCSI mode, device dependent
•
OFF to operate in slow SCSI mode
Default Settings
The default settings for the FAST_SCSI_A and FAST_SCSI_
B commands are OFF. Therefore, the SCSI controllers are
initialized to operate in slow SCSI mode.
Command
Example
To set the FAST_SCSI_A and FAST_SCSI_B commands, enter
the appropriate command. The system responds as shown.
>>> SET FAST_SCSI_A ON
Return
FAST_SCSI_A = ON
>>>
Using the ON parameter changes the default setting.
13–30
Summary of Contents for DEC 3000 600 AXP
