Cisco Small Business Pro SPA 502G Administration Manual Download Page 109

Page: 109 / 300

Configuring SIP, SPCP, and NAT

Configuring SIP

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

SIP Debug Option

SIP messages are received at or sent from the proxy listen
port. This feature controls which SIP messages to log. Choices
are as follows:

•

none—No logging.

•

1-line—Logs the start-line only for all messages.

•

1-line excl. OPT—Logs the start-line only for all messages
except OPTIONS requests/responses.

•

1-line excl. NTFY—Logs the start-line only for all messages
except NOTIFY requests/responses.

•

1-line excl. REG—Logs the start-line only for all messages
except REGISTER requests/responses.

•

1-line excl. OPT|NTFY|REG—Logs the start-line only for all
messages except OPTIONS, NOTIFY, and REGISTER
requests/responses.

•

full—Logs all SIP messages in full text.

•

full excl. OPT—Logs all SIP messages in full text except
OPTIONS requests/responses.

•

full excl. NTFY—Logs all SIP messages in full text except
NOTIFY requests/responses.

•

full excl. REG—Logs all SIP messages in full text except
REGISTER requests/responses.

•

full excl. OPT|NTFY|REG—Logs all SIP messages in full text
except for OPTIONS, NOTIFY, and REGISTER requests/
responses.

Defaults to none.

Refer Target Bye
Delay

For the Refer Target Bye Delay, enter the appropriate period of
time in seconds.

Defaults to 0.

Sticky 183

If this feature is enabled, the IP telephony ignores further 180
SIP responses after receiving the first 183 SIP response for an
outbound INVITE. To enable this feature, select yes. Otherwise,
select no.

Defaults to no.

Parameter

Description

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Search results

Summary of Contents for Small Business Pro SPA 502G

Reviews:

Related manuals for Small Business Pro SPA 502G

Brands by name

Popular brands

Cisco Small Business Pro SPA 502G, Administration Manual

Search results

Summary of Contents for Small Business Pro SPA 502G

Reviews:

Related manuals for Small Business Pro SPA 502G

Brands by name

Popular brands