Cisco Small Business Pro SPA 502G Administration Manual Download Page 235 | Manualshive

Page: 235 / 300

background image

Cisco SPA 500 Series and Wireless IP Phone Field Reference

SIP Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

224

B

STUN Test Enable

If the STUN Enable feature is enabled and a valid STUN
server is available, the IP phone can perform a NAT-
type discovery operation when it powers on. It
contacts the configured STUN server, and the result of
the discovery is reported in a Warning header in all
subsequent REGISTER requests. If the IP phone
detects symmetric NAT or a symmetric firewall, NAT
mapping is disabled.

Defaults to no.

STUN Server

IP address or fully-qualified domain name of the STUN
server to contact for NAT mapping discovery. You can
use a public STUN server or set up your own STUN
server.

EXT IP

External IP address to substitute for the actual IP
address of the IP phone in all outgoing SIP messages.
If 0.0.0.0 is specified, no IP address substitution is
performed.

If this parameter is specified, the IP phone assumes
this IP address when generating SIP messages and
SDP (if NAT Mapping is enabled for that line). However,
the results of STUN and VIA received parameter
processing, if available, supersede this statically
configured value.

Defaults to blank.

EXT RTP Port Min

External port mapping number of the RTP Port Min.
number. If this value is not zero, the RTP port number in
all outgoing SIP messages is substituted for the
corresponding port value in the external RTP port
range.

Defaults to blank.

NAT Keep Alive Intvl

Interval between NAT-mapping keep alive messages.

Defaults to 15.

Parameter

Description

«
...
233
234
235
236
237
...
»

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

KXTGA820 - EXPND DIGITAL CORDLESS HANDSET

Brand: Panasonic Pages: 5

Brand: i-SERV Pages: 28

Brand: AT&T Pages: 116

Brand: Teltonika Pages: 4

Brand: AG Neovo Pages: 33

Brand: NEO Smartpen Pages: 6

Brand: Binatone Pages: 2

Brand: MIRABELLA Pages: 18

Brand: LENCO Pages: 3

Brand: Aluratek Pages: 1

Brand: Grandstream Networks Pages: 40

Brand: BZB Gear Pages: 32

Brand: Oregon Scientific Pages: 2

Dialog 4222 Office

Brand: Aastra Pages: 2

Exilim EX-ZR700

Brand: Casio Pages: 196

Brand: BT Pages: 72

centralalert CA-CX

Brand: Serene Pages: 21

Brand: jWIN Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands