manualshive.com logo in svg

Cisco Small Business Pro SPA 502G, Administration Manual

Looking for a user manual to master your Cisco Small Business Pro SPA 502G? Look no further! Download the comprehensive and free instruction manual from manualshive.com to get the most out of this high-quality product. Empower yourself with all the information you need to optimize your experience.

Share
Download
background image

Cisco SPA 500 Series and Wireless IP Phone Field Reference

Ext Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

275

B

 

Audio Configuration 

A codec resource is considered as allocated if it has been included in the SDP 
codec list of an active call, even though it eventually may not be the one chosen for 
the connection. So, if the G.729a codec is enabled and included in the codec list, 
that resource is tied up until the end of the call whether or not the call actually uses 
G.729a. If the G.729a resource is already allocated and since only one G.729a 
resource is allowed per device, no other low-bit-rate codec may be allocated for 
subsequent calls; the only choices are G711a and G711u. On the other hand, two 
G.723.1/G.726 resources are available per device. 

Therefore it is important to disable the use of G.729a in order to guarantee the 
support of two simultaneous uses of the G.723/G.726 codecs.

Parameter

Description

Preferred Codec 

Preferred codec for all calls. (The actual codec used in 
a call still depends on the outcome of the codec 
negotiation protocol.) Select one of the following: 
G711u, G711a, G722, G726-16, G726-24, G726-32, 
G726-40, G729a, or G723.

NOTE

Cisco SPA 525G choices are: G711u, G711a, 

G726-32, G729a, and G722. G722 not available on 
WIP310.

Defaults to G711u.

Use Pref Codec Only 

To use only the preferred codec for all calls, select yes. 
(The call fails if the far end does not support this 
codec.) Otherwise, select no.

Defaults to no.

Second Preferred Codec

The second preferred codec when the preferred 
codec cannot be used. If

 Use Pref Codec Only i

s 

enabled (set to yes), this parameter is not used.

Defaults to Unspecified.

Third Preferred Codec

The third preferred codec when the preferred codec 
and second preferred codec cannot be used. If

 Use 

Pref Codec Only i

s enabled (set to yes), this parameter 

is not used.

Defaults to Unspecified.

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

NEC ML440 User Manual preview
ML440
Brand: NEC Pages: 42
NEC DT920 Customer Training Manual preview
DT920
Brand: NEC Pages: 8
NEC UX5000 Resource Manual preview
UX5000
Brand: NEC Pages: 220
NEC DT330 Quick Start Manual preview
DT330
Brand: NEC Pages: 2
NEC NEAX 2000 User Manual preview
NEAX 2000
Brand: NEC Pages: 10
NEC NEAX 2000IVS2 User Manual preview
NEAX 2000IVS2
Brand: NEC Pages: 27
ARTRAY ARTCAM-265IMX-BW-USB3-T2 Instruction Booklet preview
ARTCAM-265IMX-BW-USB3-T2
Brand: ARTRAY Pages: 18
Yealink Yealink SIP-T22P Quick Start Quide preview
Yealink SIP-T22P
Brand: Yealink Pages: 2
Yealink T42G Quick Reference Manual preview
T42G
Brand: Yealink Pages: 3
Olympus E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital... Manual De Instruções preview
E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...
Brand: Olympus Pages: 164
Olympus E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital... Manual De Instrucciones preview
E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...
Brand: Olympus Pages: 164
Uniden D1680-4XTA Manual D'Utilisation preview
D1680-4XTA
Brand: Uniden Pages: 27
Olympus D560 - 3.2 MP Digital Camera Manuel De Référence preview
D560 - 3.2 MP Digital Camera
Brand: Olympus Pages: 171
Okina USA License Plate Capture Series Operational Manual preview
License Plate Capture Series
Brand: Okina USA Pages: 3
Pentax OPTIO 550 Operating Manual preview
OPTIO 550
Brand: Pentax Pages: 160
Ikegami ISD-A15 Instruction Manual preview
ISD-A15
Brand: Ikegami Pages: 52
Logitech 980590-0403 - Cordless Internet Handset USB VoIP Wireless Phone Quick Start Manual preview
980590-0403 - Cordless Internet Handset USB VoIP Wireless Phone
Brand: Logitech Pages: 2
Yashica MAT EM Quick Start Manual preview
MAT EM
Brand: Yashica Pages: 13

Brands by name

Popular brands

Load more brands