manualshive.com logo in svg

Cisco Small Business Pro SPA 502G, Administration Manual

Looking for a user manual to master your Cisco Small Business Pro SPA 502G? Look no further! Download the comprehensive and free instruction manual from manualshive.com to get the most out of this high-quality product. Empower yourself with all the information you need to optimize your experience.

Share
Download
background image

Cisco SPA 500 Series and Wireless IP Phone Field Reference

SIP Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

219

B

 

RTCP Tx Interval 

Interval for sending out RTCP sender reports on an 
active connection. It can range from 0 to 255 seconds. 
During an active connection, the IP phone can be 
programmed to send out compound RTCP packet on 
the connection. Each compound RTP packet except 
the last one contains a SR (Sender Report) and a SDES 
(Source Description). The last RTCP packet contains an 
additional BYE packet. Each SR except the last one 
contains exactly 1 RR (Receiver Report); the last SR 
carries no RR. The SDES contains CNAME, NAME, and 
TOOL identifiers. The CNAME is set to <User 
ID>@<Proxy>, NAME is set to <Display Name> (or 
Anonymous if user blocks caller ID), and TOOL is set to 
the Vendor/Hardware-platform-software-version (such 
as Cisco/IP phone-1.0.31(b)). The NTP timestamp used 
in the SR is a snapshot of the IP phone’s local time, not 
the time reported by an NTP server. If the IP phone 
receives a RR from the peer, it attempts to compute the 
round trip delay and show it as the <Call Round Trip 
Delay> value (ms) in the Info section of IP phone web 
page.

Defaults to 0.

No UDP Checksum 

Select yes if you want the IP phone to calculate the 
UDP header checksum for SIP messages. Otherwise, 
select no.

Defaults to no.

Symmetric RTP

Enable symmetric RTP operation. If enabled, sends 
RTP packets to the source address and port of the last 
received valid inbound RTP packet. If disabled (or 
before the first RTP packet arrives) sends RTP to the 
destination as indicated in the inbound SDP.

Defaults to no.

Parameter

Description

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

Yealink T60 Quick Reference preview
T60
Brand: Yealink Pages: 2
Panasonic KX-TDE200 User Manual preview
KX-TDE200
Brand: Panasonic Pages: 252
Panasonic KX-TH112 - Cordless Phone - Operation Quick Manual preview
KX-TH112 - Cordless Phone - Operation
Brand: Panasonic Pages: 10
Unify OpenStage 15 Manual preview
OpenStage 15
Brand: Unify Pages: 19
Lanoptik MC Series User Manual preview
MC Series
Brand: Lanoptik Pages: 12
Idis DC-B1803 Installation Manual preview
DC-B1803
Brand: Idis Pages: 22
Olympus FE-4020 Manual De Instruções preview
FE-4020
Brand: Olympus Pages: 61
Olympus FE-4000 Specifications preview
FE-4000
Brand: Olympus Pages: 3
Olympus FE-26 - Digital Camera - Compact Manual De Instruções preview
FE-26 - Digital Camera - Compact
Brand: Olympus Pages: 60
Olympus FE-25 Manual De Instruções preview
FE-25
Brand: Olympus Pages: 62
Olympus FE-200 Quick Start Manual preview
FE-200
Brand: Olympus Pages: 2
Olympus FE 3000 - Digital Camera - Compact Basic Manual preview
FE 3000 - Digital Camera - Compact
Brand: Olympus Pages: 172
Olympus FE 300 - Digital Camera - Compact Manuel D'Instructions preview
FE 300 - Digital Camera - Compact
Brand: Olympus Pages: 64
Olympus FE 250 - Digital Camera - Compact Manuel Avancé preview
FE 250 - Digital Camera - Compact
Brand: Olympus Pages: 75
Olympus FE 250 - Digital Camera - Compact Specifications preview
FE 250 - Digital Camera - Compact
Brand: Olympus Pages: 2
Olympus FE 230 - Digital Camera - Compact Manual Avanzado preview
FE 230 - Digital Camera - Compact
Brand: Olympus Pages: 75
Olympus FE-200 Advanced Manual preview
FE-200
Brand: Olympus Pages: 78
Olympus FE 130 - 5.1MP Digital Camera Manual Avançado preview
FE 130 - 5.1MP Digital Camera
Brand: Olympus Pages: 80

Brands by name

Popular brands

Load more brands