Cisco Small Business Pro SPA 502G Administration Manual Download Page 137

Page: 137 / 300

Configuring Security, Quality, and Network Features

Setting Optional Network Parameters

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

126

Setting Optional Network Parameters

STEP 1

STEP 2

Click Admin Login and advanced.

STEP 3

Click the System tab.

STEP 4

Configure the following fields:

Parameter

Description

Host Name

The host name of the phone.

Domain

The network domain of the phone. However, if using
LDAP, see

Configuring Lightweight Directory Access

Protocol (LDAP) for the Cisco SPA 500 Series,
page 67

Primary DNS

DNS server used by the phone in addition to DHCP
supplied DNS servers if DHCP is enabled; when DHCP
is disabled, this is the primary DNS server.

Defaults to 0.0.0.0.

However, if using LDAP, see

Configuring Lightweight

Directory Access Protocol (LDAP) for the Cisco SPA
500 Series, page 67

Secondary DNS

DNS server used by the phone in addition to DHCP
supplied DNS servers if DHCP is enabled; when DHCP
is disabled, this is the secondary DNS server.

Defaults to 0.0.0.0.

DNS Server Order

Specifies the method for selecting the DNS server. The
options are Manual, Manual/DHCP, and DHCP/Manual.

DNS Query Mode

Do parallel or sequential DNS Query. With parallel DNS
query mode, the phone sends the same request to all
the DNS servers at the same time when doing a DNS
lookup, the first incoming reply is accepted by the
phone.

Defaults to parallel.

Not available on WIP310.

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Search results

Summary of Contents for Small Business Pro SPA 502G

Reviews:

Related manuals for Small Business Pro SPA 502G

Brands by name

Popular brands

Cisco Small Business Pro SPA 502G, Administration Manual

Search results

Summary of Contents for Small Business Pro SPA 502G

Reviews:

Related manuals for Small Business Pro SPA 502G

Brands by name

Popular brands