manualshive.com logo in svg

Cisco Small Business Pro SPA 502G, Administration Manual

Looking for a user manual to master your Cisco Small Business Pro SPA 502G? Look no further! Download the comprehensive and free instruction manual from manualshive.com to get the most out of this high-quality product. Empower yourself with all the information you need to optimize your experience.

Share
Download
background image

Cisco SPA 500 Series and Wireless IP Phone Field Reference

Phone Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

262

B

 

Missed Call Key List

Softkeys that display when a call has been missed. 
See 

Customizing Phone Softkeys, page 50

 for 

more information.

Off Hook Key List

Softkeys that display when the receiver is lifted, or 
the headphone or speakerphone buttons are 
pressed. See 

Customizing Phone Softkeys, 

page 50

 for more information.

Dialing Input Key List

Softkeys that display when the user must enter 
dialing data. See 

Customizing Phone Softkeys, 

page 50

 for more information.

Progressing Key List

Softkeys that display when a call is attempting to 
connect. See 

Customizing Phone Softkeys, 

page 50

 for more information.

Connected Key List

Softkeys that display when a call is connected. See 

Customizing Phone Softkeys, page 50

 for more 

information.

Start-Xfer Key List

Softkeys that display when a call transfer has been 
initiated. See 

Customizing Phone Softkeys, 

page 50

 for more information.

Start-Conf

Softkeys that display when a conference call has 
been initiated. See 

Customizing Phone Softkeys, 

page 50

 for more information.

Conferencing Key List

Softkeys that display when a conference call is in 
progress. See 

Customizing Phone Softkeys, 

page 50

 for more information.

Releasing Key List

Softkeys that display when a call is disconnecting. 
See 

Customizing Phone Softkeys, page 50

 for 

more information.

Hold Key List

Softkeys that display when one or more calls are on 
hold. See 

Customizing Phone Softkeys, page 50

 

for more information.

Ringing Key List

Softkeys that display when a call is incoming. See 

Customizing Phone Softkeys, page 50

 for more 

information.

Shared Active Key List

Softkeys that display when a call is active on a 
shared line. See 

Customizing Phone Softkeys, 

page 50

 for more information.

Parameter

Description

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

Canon PowerShot G6 Connection Manual preview
PowerShot G6
Brand: Canon Pages: 2
Canon EOS M10 Getting Started preview
EOS M10
Brand: Canon Pages: 21
Canon EOS 80D (W) Basic Instruction Manual preview
EOS 80D (W)
Brand: Canon Pages: 308
Canon EOS 750D Basic Instruction Manual preview
EOS 750D
Brand: Canon Pages: 212
Canon EOS 7D Mark II (G) Manual Book preview
EOS 7D Mark II (G)
Brand: Canon Pages: 26
Canon EOS M100 Getting Started Manual preview
EOS M100
Brand: Canon Pages: 15
Canon EOS M100 Help Manual preview
EOS M100
Brand: Canon Pages: 125
Canon EOS 700D Quick Reference Manual preview
EOS 700D
Brand: Canon Pages: 2
Canon EOS 6D Digital Field Manual preview
EOS 6D
Brand: Canon Pages: 24
Canon EOS 6D Mark II Function Instruction Manual preview
EOS 6D Mark II
Brand: Canon Pages: 170
Canon EOS 6D Quick Start Manual preview
EOS 6D
Brand: Canon Pages: 2
Canon EOS 6D Basic Instruction Manual preview
EOS 6D
Brand: Canon Pages: 144
Canon EOS 60D Troubleshooting Manual preview
EOS 60D
Brand: Canon Pages: 2
Canon EOS 6D Basic Manual preview
EOS 6D
Brand: Canon Pages: 148
Canon EOS 5D Mark III Manual Book preview
EOS 5D Mark III
Brand: Canon Pages: 24
Canon EOS 5DS Basic Instruction Manual preview
EOS 5DS
Brand: Canon Pages: 164
Canon EOS 7D Mark II (G) Quick Manual preview
EOS 7D Mark II (G)
Brand: Canon Pages: 2
Canon EOS 5D Mark II Booklet preview
EOS 5D Mark II
Brand: Canon Pages: 2

Brands by name

Popular brands

Load more brands