Cisco Small Business Pro SPA 502G Administration Manual Download Page 139 | Manualshive

Page: 139 / 300

background image

Configuring Security, Quality, and Network Features

Configuring VLAN Settings

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

128

5

•

Obtains the protocol addresses of neighboring devices and also discovers
the platform of those devices.

•

Shows information about the interfaces your router uses.

•

Is media and protocol-independent.

If you are using a VLAN without CDP, you must enter a VLAN ID for the IP phone.

STEP 1

Log in to the web administration interface.

STEP 2

Click Admin Login and advanced.

STEP 3

Click the System tab.

STEP 4

Enter the following parameters:

Parameter

Description

Enable VLAN

Choose Yes to enable VLAN. Choose no to
disable.

Enable CDP

Enable CDP

only if you are using a switch that

has Cisco Discovery Protocol. CDP is
negotiation based and determines which VLAN
the IP phone resides in.

VLAN ID

If you use a VLAN without CDP (VLAN enabled
and CDP disabled), enter a

VLAN ID

for the IP

phone. Note that only voice packets are tagged
with the VLAN ID.

Enable PC Port VLAN Tagging

Enables VLAN and priority tagging on the phone
data port (802.1p/q). This feature facilities
tagging of the VLAN ID (802.1Q) and priority bits
(802.1p) of the traffic coming from the PC port of
the IP phone.

Defaults to No. Choose Yes to enable the
tagging algorithm.

PC Port VLAN Highest Priority

Choose No Limit, or 0-7 (default 0). The highest
priority is 7. The priority applied to all frames,
tagged and untagged. The phone modifies the
frame priority only if the incoming frame priority
is higher than this value.

«
...
137
138
139
140
141
...
»

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

Brand: Samsung Pages: 68

Brand: Samsung Pages: 89

Brand: Samsung Pages: 72

Brand: Samsung Pages: 59

Brand: Samsung Pages: 42

Brand: Samsung Pages: 15

Brand: Zenza Bronica Pages: 21

Brand: Navitar Pages: 1

Brand: Panasonic Pages: 120

Brand: BBK Pages: 18

Brand: 3Com Pages: 98

Brand: Altigen Pages: 6

Brand: Festo Pages: 156

Brand: Konica Minolta Pages: 126

Brand: Genie Pages: 10

Brand: Planet Pages: 4

Brand: Tempo Fitness Pages: 6

Brand: Samsung Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands