Cisco Small Business Pro SPA 502G Administration Manual Download Page 209

Page: 209 / 300

Cisco SPA 500 Series and Wireless IP Phone Field Reference

Info Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

198

Current Gateway

Displays the default router assigned to the IP phone.

Primary DNS

Displays the primary DNS server assigned to the IP
phone.

Secondary DNS

Displays the secondary DNS server assigned to the IP
phone.

NTP Enable (Cisco SPA 525G
only)

Shows if Network Time Protocol is enabled.

Primary NTP Server (Cisco
SPA 525G only)

IP Address of the primary NTP server.

Secondary NTP Server
(Cisco SPA 525G only)

IP Address of the secondary NTP server.

TFTP Server (Cisco SPA
525G only)

Address of the TFTP server for provisioning.

Bluetooth Enabled (Cisco SPA
525G only)

Shows if Bluetooth is enabled.

Bluetooth Firmware Version
(Cisco SPA 525G only)

Displays the Bluetooth firmware version.

Bluetooth Connected (Cisco
SPA 525G only)

Shows if a Bluetooth device is connected to the phone.

Bluetooth MAC (Cisco SPA
525G only)

Shows the hardware address of the Bluetooth device.

Connected Device ID (Cisco
SPA 525G only)

Shows the name of the connected Bluetooth device.

Wireless Enabled (Cisco SPA
525G only)

Shows if Wireless-G is enabled on the phone.

Wireless Connected (Cisco
SPA 525G only)

Shows if the phone is connected to the wireless
network.

Wireless MAC (Cisco SPA
525G only)

Shows the hardware address of the Wireless-G
controller.

SSID (Cisco SPA 525G only)

Shows the SSID, or name of the wireless router to
which the phone is connected.

Parameter

Description

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Search results

Summary of Contents for Small Business Pro SPA 502G

Reviews:

Related manuals for Small Business Pro SPA 502G

Brands by name

Popular brands

Cisco Small Business Pro SPA 502G, Administration Manual

Search results

Summary of Contents for Small Business Pro SPA 502G

Reviews:

Related manuals for Small Business Pro SPA 502G

Brands by name

Popular brands