Cisco Small Business Pro SPA 502G Administration Manual Download Page 149 | Manualshive

Page: 149 / 300

background image

Provisioning Basics

Sample Configuration File

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

138

6

General Purpose Parameters

These are configured in the General Purpose Parameters section of the
Provisioning tab. These parameters can be used as variables in provisioning and
upgrade rules. They are referenced by prepending the variable name with a ‘$’
character, such as $GPP_A.

You can optionally Require Admin Password to Reset Unit to Factory Defaults (see
last line of sample config file).

Sample Configuration File

Following is a sample configuration file:

Set_Local_Date_(mm/dd) "" ;

Set_Local_Time_(HH/mm) "" ;

Time_Zone "GMT-07:00" ; # options: GMT-12:00/GMT-11:00/GMT-10:00/GMT-09:00/

GMT-08:00/GMT-07:00/GMT-06:00/GMT-05:00/GMT-04:00/GMT-03:30/GMT-03:00/GMT-

02:00/GMT-01:00/GMT/GMT+01:00/GMT+02:00/GMT+03:00/GMT+03:30/GMT+04:00/

GMT+05:00/GMT+05:30/GMT+05:45/GMT+06:00/GMT+06:30/GMT+07:00/GMT+08:00/

GMT+09:00/GMT+09:30/GMT+10:00/GMT+11:00/GMT+12:00/GMT+13:00

FXS_Port_Impedance "600" ; # options: 600/900/600+2.16uF/900+2.16uF/

270+750||150nF/220+820||120nF/220+820||115nF/370+620||310nF

FXS_Port_Input_Gain "-3" ;

FXS_Port_Output_Gain "-3" ;

DTMF_Playback_Level "-16" ;

DTMF_Playback_Length ".1" ;

Detect_ABCD "Yes" ;

Playback_ABCD "Yes" ;

Caller_ID_Method "Bellcore(N.Amer,China)" ; # options:

Bellcore(N.Amer,China)/DTMF(Finland,Sweden)/DTMF(Denmark)/ETSI DTMF/ETSI

DTMF With PR/ETSI DTMF After Ring/ETSI FSK/ETSI FSK With PR(UK)

FXS_Port_Power_Limit "3" ; # options: 1/2/3/4/5/6/7/8

Protect_IVR_FactoryReset “No” ;

NOTE

You can optionally require an admin password to reset the phone to factory
defaults by setting the last line parameter to “yes.”

If you are a service provider with a password, see the

Cisco Small Business IP

Telephony Devices Provisioning Guide.

«
...
147
148
149
150
151
...
»

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 64

Brand: Panasonic Pages: 87

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 214

Brand: Panasonic Pages: 126

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands