Cisco Small Business Pro SPA 502G Administration Manual Download Page 280 | Manualshive

Page: 280 / 300

background image

Cisco SPA 500 Series and Wireless IP Phone Field Reference

Ext Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

269

B

Call Feature Settings

Auth INVITE

When enabled, authorization is required for initial
incoming INVITE requests from the SIP proxy.

Ntfy Refer On 1xx-To-Inv

If set to yes, as a transferee, the phone will send a
NOTIFY with Event:Refer to the transferor for any 1xx
response returned by the transfer target, on the
transfer call leg.

If set to no, the phone will only send a NOTIFY for final
responses (200 and higher).

NOTE

Not applicable to the WIP310.

Use Anonymous With RPID

This parameter applies only if <SIP Remote-Party-ID>
is set to yes; otherwise, it is ignored.

If the parameter is set to yes, the FROM header's
display-name and user-id fields are set to anonymous
when the caller blocks his caller-id. If the parameter is
set to no, the FROM header's display-name and user-id
are not masked. The Remote-Party-ID header indicates
privacy=full when the caller wishes to block his caller-
id.

Default: yes.

NOTE

Not applicable to the WIP310.

Set G729annexb

Configure G.729 Annex B settings.

NOTE

Not applicable to Cisco SPA 525G.

Parameter

Description

Parameter

Description

Blind Attn-Xfer Enable

Enables the IP phone to perform an attended transfer
operation by ending the current call leg and
performing a blind transfer of the other call leg. If this
feature is disabled, the IP phone performs an attended
transfer operation by referring the other call leg to the
current call leg while maintaining both call legs. To use
this feature, select yes. Otherwise, select no.

Defaults to no.

«
...
278
279
280
281
282
...
»

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

Brand: Canon Pages: 21

Brand: Canon Pages: 308

Brand: Canon Pages: 212

EOS 7D Mark II (G)

Brand: Canon Pages: 26

Brand: Canon Pages: 15

Brand: Canon Pages: 125

Brand: Canon Pages: 2

Brand: Canon Pages: 24

Brand: Canon Pages: 170

Brand: Canon Pages: 2

Brand: Canon Pages: 144

Brand: Canon Pages: 2

Brand: Canon Pages: 148

EOS 5D Mark III

Brand: Canon Pages: 24

Brand: Canon Pages: 164

EOS 7D Mark II (G)

Brand: Canon Pages: 2

Brand: Canon Pages: 2

EOS Rebel SL1 18-55mm IS STM Kit

Brand: Canon Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands