Cisco Small Business Pro SPA 502G Administration Manual Download Page 225 | Manualshive

Page: 225 / 300

background image

Cisco SPA 500 Series and Wireless IP Phone Field Reference

SIP Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

214

B

Mark All AVT packets

If set to yes, all audio video transport (AVT) tone
packets (encoded for redundancy) have the marker bit
set. If set to no, only the first packet has the marker bit
set for each DTMF event.

Defaults to yes.

SIP TCP Port Min

Specifies the lowest TCP port number that can be
used for SIP sessions. Defaults to 5060.

SIP TCP Port Max

Specifies the highest TCP port number that can be
used for SIP sessions. Defaults to 5080.

CTI Enable

The CTI interface allows a third-party application to
control and monitor the state of a phone that has
registered with the Cisco SPA 9000. With this interface,
an application can control a phone to initiate an
outgoing call or answer an incoming call with a mouse
click from a PC.

Caller ID Header

Provides the option to take the caller ID from PAID-
RPID-FROM, P-ASSERTEDIDENTITY, REMOTE-PARTY-
ID, or FROM header.

SRTP Method

Selects the method to use for SRTP. Two choices are
available:

•

x-sipura—legacy SRPT method

•

s-descriptor—new method compliant with RFC-
3711 and RFC-4568

The default value is "x-sipura.”

NOTE

Not applicable to WIP310.

Hold Target Before REFER

Controls whether to hold call leg with transfer target
before sending REFER to the transferee when initiating
a fully-attended call transfer (where the transfer target
has answered). Default value is "no,” where the call leg
is not held.

NOTE

Not applicable to WIP310.

Parameter

Description

«
...
223
224
225
226
227
...
»

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

Brand: Olympus Pages: 84

Brand: Olympus Pages: 83

OpenScape CP600

Brand: Unify Pages: 32

OpenScape CP700

Brand: Unify Pages: 24

OpenScape CP200

Brand: Unify Pages: 2

OpenScape CP600

Brand: Unify Pages: 2

OpenScape Desk Phone IP 35G

Brand: Unify Pages: 130

Brand: Unify Pages: 2

Brand: Unifat Technology Pages: 6

Brand: ViewSonic Pages: 1

CRUISER2 HSF002

Brand: Jabra Pages: 2

Brand: Konica Minolta Pages: 126

T737 - Digital Camera - Compact

Brand: Polaroid Pages: 58

Brand: Loocam Pages: 8

Brand: Vivitar Pages: 68

Brand: VADDIO Pages: 69

Aegis-09 Series

Brand: Scitec Pages: 4

Brand: OCL Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands