manualshive.com logo in svg

Cisco Small Business Pro SPA 502G, Administration Manual

Looking for a user manual to master your Cisco Small Business Pro SPA 502G? Look no further! Download the comprehensive and free instruction manual from manualshive.com to get the most out of this high-quality product. Empower yourself with all the information you need to optimize your experience.

Share
Download
background image

Cisco SPA 500 Series and Wireless IP Phone Field Reference

Provisioning Tab

Cisco SPA 500 Series and WIP310 IP Phone Administration Guide

225

B

 

Linksys Key System Parameters

Provisioning Tab

NOTE

For information about the Provisioning page, see the 

Cisco Small Business IP 

Telephony Devices Provisioning Guide

.

Regional Tab

This section describes the fields for the following headings on the Regional tab:

•

Call Progress Tones, page 226

•

Distinctive Ring Patterns, page 229

Parameter

Description

Linksys Key System

Enable or disable the Linksys Key System on the IP 
phone.

Defaults to yes.

Multicast Address

The multicast address is used by the Cisco SPA 9000 
to communicate with the Cisco SPA IP phones. 

Defaults to 224.168.168.168:6061.

Key System Auto Discovery

Enables or disables auto discovery of the call control 
server (for example, the Cisco SPA 9000). Disable this 
feature for teleworkers or other scenarios where 
multicast does not work.

Key System IP Address

IP address of the call control server IP. Enter the IP 
address for teleworkers or other scenarios where 
multicast does not work.

Force LAN Codec

The choices are: none, G.711u, or G.711a. Defaults to 
none. 

Summary of Contents for Small Business Pro SPA 502G













































































































































































































































































































Reviews:

No comments

Related manuals for Small Business Pro SPA 502G

JAI SP-5000M-USB User Manual preview
SP-5000M-USB
Brand: JAI Pages: 71
Samsung SL105 Manual Del Usuario preview
SL105
Brand: Samsung Pages: 98
Samsung SAMSUNG SH100 Firmware Upgrade Manual preview
SAMSUNG SH100
Brand: Samsung Pages: 4
Samsung SAMSUNG ST200F Manual Del Usuario preview
SAMSUNG ST200F
Brand: Samsung Pages: 161
Samsung SAMSUNG PL55 Schematic Diagrams preview
SAMSUNG PL55
Brand: Samsung Pages: 14
Samsung SAMSUNG M110 User Manual preview
SAMSUNG M110
Brand: Samsung Pages: 103
Samsung SAMSUNG I100 Getting To Know Manual preview
SAMSUNG I100
Brand: Samsung Pages: 128
Samsung S1050 - Digital Camera - Compact Manual De Usuario preview
S1050 - Digital Camera - Compact
Brand: Samsung Pages: 100
Samsung PL70 Schematic Diagrams preview
PL70
Brand: Samsung Pages: 8
Samsung PL70 Technical Information preview
PL70
Brand: Samsung Pages: 96
Samsung SAMSUNG PL55 User Manual preview
SAMSUNG PL55
Brand: Samsung Pages: 103
Samsung PL10 User Manual preview
PL10
Brand: Samsung Pages: 104
Samsung MV900F Manual Del Usuario preview
MV900F
Brand: Samsung Pages: 173
Samsung SCB-6001 Quick Manual preview
SCB-6001
Brand: Samsung Pages: 2
Samsung SL35 - Digital Camera - Compact User Manual preview
SL35 - Digital Camera - Compact
Brand: Samsung Pages: 102
Samsung P10 Manual preview
P10
Brand: Samsung Pages: 98
Samsung SL202 - Digital Camera - Compact Quick Start Manual preview
SL202 - Digital Camera - Compact
Brand: Samsung Pages: 22
Samsung S1060 Quick Start Quide preview
S1060
Brand: Samsung Pages: 82

Brands by name

Popular brands

Load more brands