![background image](http://html1.mh-extra.com/html/carrier/vector-1800-mt/vector-1800-mt_operation-and-service-manual_2564194196.webp)
62-11039
7-65
Alarm
NO.
Steps
ALARM / CAUSE
CORRECTIVE ACTION
137 C2 CHECK RETURN AIR SENSOR (2RAT)
•
TRIGGER–ON: Return Air Sensor 2 is not within the range of --53
°
F to +158
°
F (--47
°
C to +70
°
C)
•
UNIT CONTROL: Engine and standby: If setpoint is in the perishable range, compartment 2 will shut
UNIT CONTROL: Engine and standby: If setpoint is in the perishable range, compartment 2 will shut
down. If setpoint is in the frozen range, compartment 2 will run in reduced capacity cool.
•
RESET CONDITION: Auto Reset when sensor is in range or, alarm may be manually reset via keypad or
by turning the unit off, then back on again.
NOTE: Follow the steps below until a problem is found. Once a repair or correction has been made, the active alarm
should clear itself (see reset condition above). Operate the unit through the appropriate modes to see if any active
alarm occurs. Continue with the steps below as necessary.
1.
Check 2RAT Sensor
a. Inspect Return Air Sensor & connector No damage to sensor
No damage, moisture, or corrosion in connector
b. Check Return Air Sensor resistance
(See Note 4)
(Refer to Table 8-8 for complete resistance chart)
10,000 Ohms @ 77
°
F (25
°
C)
2.
Check 2RAT Wiring
a. Inspect harness & control box
connector pins & terminals (See
wiring schematic)
No physical damage to harness.
No damaged or corroded pins
138 C3 CHECK RETURN AIR SENSOR (3RAT)
•
TRIGGER–ON: Return Air Sensor 3 is not within the range of --53
°
F to +158
°
F (--47
°
C to +70
°
C)
•
UNIT CONTROL: Engine and standby: If setpoint is in the perishable range, compartment 3 will shut
UNIT CONTROL: Engine and standby: If setpoint is in the perishable range, compartment 3 will shut
down. If setpoint is in the frozen range, compartment 3 will run in reduced capacity cool.
•
RESET CONDITION: Auto Reset when sensor is in range or, alarm may be manually reset via keypad or
by turning the unit off, then back on again.
NOTE: Follow the steps below until a problem is found. Once a repair or correction has been made, the active alarm
should clear itself (see reset condition above). Operate the unit through the appropriate modes to see if any active
alarm occurs. Continue with the steps below as necessary.
1.
Check 3RAT Sensor
a. Inspect Return Air Sensor & connector No damage to sensor
No damage, moisture, or corrosion in connector
b. Check Return Air Sensor resistance
(See Note 4)
(Refer to Table 8-8 for complete resistance chart)
10,000 Ohms @ 77
°
F (25
°
C)
2.
Check 3RAT Wiring
a. Inspect harness & control box
connector pins & terminals (See
wiring schematic)
No physical damage to harness.
No damaged or corroded pins
Summary of Contents for VECTOR 1800 MT
