CAE SimuFlite Citation Bravo Pilot Training Manual Download | Manualshive

Page: 456 / 718

background image

5B-82

Developed for Training Purposes

Citation Bravo

September 2005

CAE SimuFlite

Attitude and
Heading Reference

The attitude and heading reference
systems provide pitch, roll, and sta-
bilized heading reference informa-
tion to the flight control, flight
instrument, and weather radar sys-
tems. The system consists of:

n

VG-14A Vertical Gyros

n

C-14D Directional Gyros

n

RG-204 Rate Gyro.

Vertical Gyros

The Honeywell VG-14A Vertical
Gyro provides pitch and roll attitude
information to the EADI, flight
director, autopilot, and weather
radar. The weather radar uses pitch
and roll information for antenna sta-
bilization.

The gyro consists of an electrically-
driven gyro rotor, pitch and roll syn-
chros, torquers, gravity erection sys-
tem, and monitoring circuits.
Gimbals within the unit limit the
amount of movement around the
pitch and roll axes. The gyro is free
to move 80° up and down and 360°
around the roll axis. Pitch and roll
torquers erect the rotor to prevent
gyro tumble.

As the aircraft moves about its pitch
and roll axes, the pitch and roll syn-
chros react to the movement of the
gyro gimbal. As the gimbal moves,
the synchros provide electrical sig-
nals proportional to the gyro dis-
placement.

Directional Gyros

The aircraft has dual Honeywell C-
14D compass systems for the pilot
and copilot. Both provide 360° of
magnetic heading information to the
HSIs, RMIs, autopilot, flight direc-
tor, and other guidance systems.

Each system consists of a directional
gyro, flux valve, remote compensa-
tor, and control switch.

Each directional gyro has an electri-
cally driven gyro and a base assem-
bly with an inverter. The pilot's
compass system receives power
from the Emergency bus on the right
circuit breaker panel and the copi-
lot's system receives power from the
Right Main Extension bus. If the
main AC inverters fail, the copilot's
compass system inverter provides
26V AC power to No. 2 navigation
radio (NAV 2) and the copilot's HSI.

The flux valve senses the strength
and direction of the earth's magnetic
field and converts it into electrical
signals for gyro compensation. The
compensating signal aligns the gyro
with magnetic north. The remote
compensator uses adjustable perma-
nent magnets to counteract the effect
of magnetic fields on the flux valves
created by direct current and ferrous
materials in the aircraft.

The GYRO MAN/AUTO switches
control the C-14D compass systems.
In AUTO, the gyro automatically
aligns itself to the magnetic heading
indicated by the flux valve. In MAN,
manual gyro alignment is through a
spring-return L/R SLAVE switch.

«
...
454
455
456
457
458
...
»

Summary of Contents for Citation Bravo















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Citation Bravo

Brand: Keithley Pages: 36

Brand: Rain-Flo Irrigation Pages: 16

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: idiag Pages: 12

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: Tascam Pages: 8

Brand: NanoVibronix Pages: 2

Brand: NanoVibronix Pages: 32

Shapes Hexagons

Brand: Nanoleaf Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands