manualshive.com logo in svg

CAE SimuFlite Citation Bravo, Pilot Training Manual

The CAE SimuFlite Citation Bravo pilot training manual is an essential resource for mastering the intricacies of flying this aircraft. Download this comprehensive manual for free from our website manualshive.com to access a wealth of information, ensuring a safe and knowledgeable flight experience.

Share
Download
background image

5B-60

Developed for Training Purposes

Citation Bravo

March 2009

CAE SimuFlite

Flight Instruments

The flight instrumentation system
presents information on three elec-
tronic display units, two PFDs and
one MFD, which can present a vari-
ety of information in compact
arrangements and in a variety of for-
mats. Presentations that are not nec-
essary can be removed and/or
replaced with more appropriate data
for the existing flight conditions. The
components of the system include:

n

PFD Display Units And Controllers

n

Multifunction Display Unit and
Controller

n

Symbol Generators

n

Remote Instrument Controller 

n

Standby Attitude Indicator

n

Meggitt Standby Instrument

n

Standby Airspeed/Altimeter.

DC-550 Display Controller

The DC-550 Display Controllers (see

Figure 5B-47) 

to the left and right of

pilot's and copilot's PFD, respec-
tively, allow selection of the different
display formats and provide for selec-
tion of required navigation sources
and bearing data for the EADI and
EHSI displays. The detection of a
failure in the display controller dis-
plays MENU INOP on the MFD.
Buttons on the controller include:
HSI - Toggles the EHSI display
between full or partial (arc) compass
displays; displays 360° in FULL
mode and 90° in WX mode. The
powerup default is full compass.
SC/CP - Selects the flight director
command display mode. Alternat-
ing action toggles between single
cue “command bars” (power-up
mode) and cross pointer displays.
Both command modes displays a
nose up pitch attitude of 12° when
Go-Around switch on the throttle is
pressed.

IN/HPA - Selects the altimeter BARO
correction display; toggles between
inHg and hPa measurements. The
power up default is the same mode that
existed at powerdown. Selecting HPA
displays the altitude digits in meters.
GSPD/TTG - Toggles between
groundspeed (GSPD) and Time-To-
Go (TTG) on the EHSI display and
provides alternating selection of
groundspeed or time-to-go to the next
station or waypoint. The power-up
default is groundspeed.
ET - Replaces the GSPD/TTG func-
tion with a digital clock display. Initial
actuation enters the mode at the previ-
ous position. The clock can be started,
stopped, and reset with multiple
pushes of the ET button.
NAV - Selects VOR on the PFD dis-
play course deviation indicator (CDI)
and alternately selects between NAV 1
and NAV 2 (annunciated VOR 1 and
VOR 2) or between ILS 1 AND ILS 2,
if the ILS frequency is tuned in NAV
The power-up default is the onside
(green) VOR 1/ILS 1. After power-up,
pressing the NAV button displays the
cross-side (yellow) VOR 2/ILS 2
information.
FMS - Selects flight management
system information on the EHSI dis-
play in magenta; the course needle
represents FMS information on the
bearing pointer. On aircraft equipped
with optional dual FMS systems, this
toggles between FMS 1 and FMS 2.
The PFD DIM knob sets the overall
brightness of the PFD. When the
pilot sets the reference level, photo-
electric sensors maintain the relative
brightness under various lighting
conditions. Full counterclockwise
OFF turns off the PFD and reverts
the display, through the backup
mode, to the MFD. 

Summary of Contents for Citation Bravo















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Citation Bravo

ACE INSTRUMENTS WAVE Operating Manual preview
WAVE
Brand: ACE INSTRUMENTS Pages: 15
Wave Fitness Neptune Owner'S Manual preview
Neptune
Brand: Wave Fitness Pages: 15
Mandam MCH Series Instruction Manual preview
MCH Series
Brand: Mandam Pages: 9
Major 4200 Operator'S Manual & Parts List preview
4200
Brand: Major Pages: 52
MAGIC FX CO2JET II User And Installation Manual preview
CO2JET II
Brand: MAGIC FX Pages: 25
Pace ThermoTweez Handpiece TT-65 Operation & Maintenance Instructions Manual preview
ThermoTweez Handpiece TT-65
Brand: Pace Pages: 14
Rainin Instrument P-10 Manual preview
P-10
Brand: Rainin Instrument Pages: 16
TC Electronic M-ONE Quick Manual preview
M-ONE
Brand: TC Electronic Pages: 4
TC Electronic VORTEX MINI Quick Start Manual preview
VORTEX MINI
Brand: TC Electronic Pages: 6
TC-Helicon SINGTHING User Manual preview
SINGTHING
Brand: TC-Helicon Pages: 12
TC Electronic DB6 Manual preview
DB6
Brand: TC Electronic Pages: 76
Ultraflex A97 Installation And Maintenance Manual preview
A97
Brand: Ultraflex Pages: 48
Salter PT-1700 Owner'S Manual preview
PT-1700
Brand: Salter Pages: 18
Salter KOR M-9590 Owner'S Manual preview
KOR M-9590
Brand: Salter Pages: 42
Salter KOR M-9530 Owner'S Manual preview
KOR M-9530
Brand: Salter Pages: 47
Salter FENX M-9640/L Owner'S Manual preview
FENX M-9640/L
Brand: Salter Pages: 35
Salter FENX M-9690 Owner'S Manual preview
FENX M-9690
Brand: Salter Pages: 40
Salter M-041 INDOOR CROSS Owner'S Manual preview
M-041 INDOOR CROSS
Brand: Salter Pages: 15

Brands by name

Popular brands

Load more brands