Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 72

Page: 72 / 422

4.3.3

Mounting position

Mounting positions of components

Risk of damage to the components by

incorrect mounting position!

NOTICE

Only operate the components in their allowed mounting positions. The

allowed mounting positions are specified in the technical data of the

components.

For supply units and drive controllers installed in control cabinets, only the

mounting position G1 is usually allowed.
Some components can also be operated in mounting positions other than G1.

The allowed mounting positions are specified in the technical data of the

component.

Mounting positions

The allowed mounting positions are specified with G1, G2, G3, G4 or G5 in

the technical data of the components.

Mounting

position

Description

Normal mounting position
The air heated inside the component can flow

unimpeded vertically upward. In the case of

components with integrated fans, the natural

convection supports the forced cooling air current.

Mounting surface

Outgoing, heated air

Component

Fan within the component (forces the cooling air

current)

Cooling air

180° to normal mounting position

90° to normal mounting position

bottom mounting; mounting surface on the bottom

top mounting; mounting surface at the top

Tab. 4-12:

Mounting positions

58/407

General data and specifications

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands