Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 292

Page: 292 / 422

Cover for connection point

Protective sleeve for shaft

Fig. 9-1:

Protective sleeves

●

Avoid damage to the motor flange and drive shaft.

●

Avoid impacts on the drive shaft.

Fig. 9-2:

Handling the shaft end

Impacts on the shaft end damage encoder and ball bearing! Driving

elements, such as pulleys, coupling disks or toothed wheels, may only be

mounted or dismounted by evenly heating up the driving elements or with the

appropriate tool for mounting and dismounting.

9.1.2

System overview

Available connection points

The electrical connections of all sizes of KSM/KMS have been standardized:
●

Two power connections (hybrid connectors for power, control voltage,

master communication and status messages) to loop through the bus

cable

●

Two I/O connectors (M12, 5-pin)

●

One safety technology interface (M12, 12-pin)

●

Optional: two connection points for connecting the communication (M12,

4-pin)

Notes

All connections have been designed as plug-in connectors. This ensures

easy, quick and error-safe mounting and commissioning when using ready-

made Rexroth connection cables.

278/407

Mounting and installation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands