Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 160

Page: 160 / 422

6.2.3

X29.1, X29.2, Multi-Ethernet

The signals at X29.1 are directly looped through to X29.2.

View

Connection

Signal name

Function

TD+

Transmit, Differential Output A

TD-

Transmit, Differential Output B

RD+

Receive, Differential Input A

n. c.

RD-

Receive, Differential Input B

n. c.

Housing

Shield connection

Properties
Standard

●

Ethernet

●

Type: RJ-45, 8-pin

Compatibility

100Base-TX according to IEEE 802.3u

Recommended cable type

●

According to CAT5e; ITP type of shield (Industrial Twisted Pair)

●

Ready-made cables that can be ordered:
–

RKB0021
Long cables (100 m at maximum) to connect the drive system to the

higher-level control unit or remote communication nodes.
Minimum bending radius:
–

48.75 mm with flexible installation

–

32.50 mm with permanent installation

Order code for a 30 m long cable: RKB0021/030,0

–

RKB0013
Short cables to connect devices arranged side by side in the control

cabinet.
4 lengths available: 0.19 m; 0.25 m; 0.35 m; 0.55 m
Order code for a 0.55 m long cable: RKB0013/00,55
Minimum bending radius: 30.75 mm

Tab. 6-4:

Function, pin assignment, properties

146/407

Connection points

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands