Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 24

Page: 24 / 422

IndraDrive Mi drive system with HMV01 supply unit:

24V

24V supply

DST

Transformer (optional)

Fuses

HMD, HMS Inverter (optional)

HMV01

Supply unit

HNF

Mains filter

HNL

Mains choke

Mains contactor (only for supply units without integrated mains

contactor, e.g. HMV01.1R-W0120)

KCU02

Drive connection box

KSM02

Motor-integrated servo drive (alternative: KMS02 near motor

servo drive and motor)

MSK

Servo motor (optional)

RHS

Terminal connector

RKB0021

Ethernet cable of variable length

RKB0013

Ethernet cable of defined length (max. 0.55 m)

RKG

Encoder cable (optional)

RKH

Hybrid cable

RKL

Motor cable (optional)

X14

Mains synchronization (only with regenerative HMVs)

X103.1

Connection of RKH hybrid cable at first KSM02

Fig. 1-3:

IndraDrive Mi drive system with HMV01

10/407

System presentation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands