Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 196

Page: 196 / 422

6.4.4

X104, motor encoder connection

Description

For encoders with a supply voltage of 12 volt (max. 60 mA):
Sin-cos encoder 1 V

; HIPERFACE®

The connection only exists at devices with an ENH encoder interface.

View

Connection

Signal name

S1, M1

(HIPERFACE®)

Function

VCC_Encoder Power supply

GND_Encoder Power supply reference potential

A +

Track A positive; cos

A -

Track A negative; refcos

B +

Track B positive; sin

B -

Track B negative; refsin

Data transmission

EncData-

Data transmission

n. c.

Overall

shield via

connector

housing

10-pin, female connector

Unit

min.

max.

Connection cable, stranded wire

n.s.

Order type of cable

RKG4201

Allowed length

n.s.

7.5

Tab. 6-34:

X104, motor encoder

6.4.5

X107, programming module

See

chapter 6.3.4 "X107, programming module" on page 165

6.4.6

X108, X109, communication output coupling

See

chapter 6.3.5 "X108, X109, communication output coupling" on page

167

6.4.7

X118, X119, external communication

See

chapter 6.3.6 "X118, X119, external communication" on page 170

6.4.8

X141, safety technology

See

chapter 6.3.7 "X141, safety technology and service input release brake"

on page 173

182/407

Connection points

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands