Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 353 | Manualshive

Page: 353 / 422

background image

11

Commissioning, operation, diagnostics and mainte‐

nance

11.1

Notes on commissioning

11.1.1

General information

High electrical voltage! Danger to life, risk of

injury by electric shock or serious injury!

WARNING

Read and observe the detailed safety instructions contained in this

documentation in chapter "Safety instructions for electric drives and controls".

11.1.2

Preparation

1. Keep the documentation of all used products ready.
2. Check the products for damage.
3. Check all mechanical and electrical connections.
4. Activate the safety devices and monitoring systems of the installation.

11.1.3

Procedure

Commission the drive system according to the instructions contained in the

corresponding product documentation. See the Functional Description of the

firmware for the corresponding information.
The commissioning of drive controllers and control unit may require additional

steps. The functionality and performance check of the installations is not part

of motor commissioning. Instead, it is carried out within the scope of the

commissioning of the machine as a whole. Observe the machine

manufacturer's specifications and instructions.

11.2

Notes on operation

WARNING! Lethal electric shock from live parts with

more than 50 V!
Never operate the KCU02 drive connection box

without the touch guard mounted.
See also

chapter 9.4.2 "Touch guard" on page 283

.

Tab. 11-1:

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

339/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

«
...
351
352
353
354
355
...
»

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Rexroth IndraDrive Mi KCU02

Brand: Eaton Pages: 50

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: K&K Pages: 6

Brand: Sole Diesel Pages: 8

ElectraElite IPK

Brand: NEC Pages: 20

Brand: rada Pages: 16

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Febco Pages: 12

Brand: Game ready Pages: 21

Brand: VAMP Pages: 304

Brand: IBM Pages: 276

Brand: IBM Pages: 32

Brand: IBM Pages: 157

Brand: Samson Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands