Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 200

Page: 200 / 422

6.5

KMS03 connection points

6.5.1

Positions of the connection points

Use ready-made hybrid cables and terminal connectors by

Rexroth for X103.1 and X103.2.
X107 (programming module) is only accessible after the cover

has been removed.

Figure

Element Significance

Address selector switch

(10×)

Address selector switch (1×)

X37
X38

Digital inputs/outputs

X103.1
X103.2

Hybrid cable

X107

Programming module

(underneath the cover)

X1x8
X1x9

Communication (optional)
●

X108, X109:
Communication output

coupling

●

X118, X119:
External

communication

X141

Safety technology (optional)

XD3

Motor

XG3

Brake/temperature

XG4

Motor encoder, digital

XG8

Motor encoder, analog
Second connection point of

equipment grounding

conductor

Tab. 6-37:

KMS03 connection points

186/407

Connection points

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands