manualshive.com logo in svg

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

The Bosch Rexroth IndraDrive Mi KCU02 is a state-of-the-art industrial drive controller. Unlock its full potential with the comprehensive Instruction Manual, available for free download on our website. This manual provides detailed guidance and insights to ensure smooth operation and maximum efficiency. Get yours now at manualshive.com!

Share
Download
background image

Personal  injury  or  property  damage  by

interrupting or connecting live lines!

WARNING

Interrupting  or  connecting  live  lines  may  cause  unpredictable  dangerous

situations or lead to property damage. Therefore:
●

Connect and disconnect plug-in connectors only when they are dry and

de-energized.

●

During  operation  of  the  installation,  all  plug-in  connectors  must  be

locked.

Risk of short circuit caused by liquid coolant

or lubricant!

WARNING

Short circuits of live lines may cause unpredictable dangerous situations or

lead to property damage. Therefore:
●

Provide exposed mating sides of power plug-in connectors with safety

caps  when  installing  or  replacing  drive  components,  if  you  cannot

exclude that they might be moistened with liquid coolant or lubricant.

9.6.2 

Notes

The motor cable is a hybrid cable in which the communication line has been

integrated.  Only  the  hybrid  cable  by  Rexroth  can  ensure  the  function.  It  is

supplied  as  ready-made  cable.  The  outgoing  direction  of  the  hybrid  cable

cannot be changed subsequently!

Risk  of  damage  by  subsequently  changing

the outgoing direction of the hybrid cable!

NOTICE

Do not try to reverse the cable outgoing direction of a ready-made connector!

The flexible leads in the connector have individual lengths for each outgoing

direction.

Risk of damage by leakage of the connection

points!

NOTICE

If  vibrations  affect  the  hybrid  cable:  Install  strain  relief  near  the  connection

points  (X103.1,  X103.2)  so  that  the  connectors  are  not  affected  by  high

vibration loads. This can avoid possible leakage (entering liquid).

When  ordering  the  ready-made  hybrid  cables,  always  indicate  the  desired

outgoing  direction:  See 

chapter  5.9.1    "RKH  hybrid  cable  incl.

communication, technical data" on page 114

.

Ready-made hybrid cables have been coded in such a way that X103.1 and

X103.2 cannot be interchanged when connecting the cables.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03  

287/407

Mounting and installation

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Rexroth IndraDrive Mi KCU02

MADRIX AURA Technical Manual & Quick Start Manual preview
AURA
Brand: MADRIX Pages: 36
U-Line H-3934 Manual preview
H-3934
Brand: U-Line Pages: 7
Samson 3430 Operating Instructions Manual preview
3430
Brand: Samson Pages: 52
Samson 3275 Mounting And Operating Instructions preview
3275
Brand: Samson Pages: 32
Danfoss Cascade Operating Instructions Manual preview
Cascade
Brand: Danfoss Pages: 59
Omega PHCN-37 User Manual preview
PHCN-37
Brand: Omega Pages: 56
Omega DP25-TC Quick Start Manuals preview
DP25-TC
Brand: Omega Pages: 2
Omega Lift 43000 Operating Instructions & Parts Manual preview
43000
Brand: Omega Lift Pages: 24
Omega Lift 28045 Operating Instructions & Parts Manual preview
28045
Brand: Omega Lift Pages: 8
OMA 542 Manual preview
542
Brand: OMA Pages: 45
Union Instruments CWD2005 SPC Operating Instructions And Safety Notes preview
CWD2005 SPC
Brand: Union Instruments Pages: 63
WAREMA Wisotronic Operating Instructions Manual preview
Wisotronic
Brand: WAREMA Pages: 112
WAGO 750-880 Manual preview
750-880
Brand: WAGO Pages: 414
V2 Blitz Manual preview
Blitz
Brand: V2 Pages: 48
WAGO WAGO-I/O-SYSTEM 750 XTR Series Manual preview
WAGO-I/O-SYSTEM 750 XTR Series
Brand: WAGO Pages: 272
WAGO I/O-SYSTEM 750 Manual preview
I/O-SYSTEM 750
Brand: WAGO Pages: 450
D+H RZN 4402-K V2 Original Instructions Manual preview
RZN 4402-K V2
Brand: D+H Pages: 32
Vag GA Industries 930-DT Installation, Operation And Maintenance Manual preview
GA Industries 930-DT
Brand: Vag Pages: 4

Brands by name

Popular brands

Load more brands