background image

12 

Environmental protection and disposal

12.1 

Environmental protection

Production processes

The  products  are  manufactured  in  energy-  and  resource-optimized

production processes which allow re-using and recycling the resulting waste.

We  regularly  try  to  replace  pollutant-loaded  raw  materials  and  supplies  by

more environment-friendly alternatives.

No release of hazardous substan‐

ces

Our  products  do  not  contain  any  hazardous  substances  which  may  be

released in case of appropriate use. Normally, our products will not have any

negative influences on the environment.

Significant components

Significant components of our products are:

Electronic devices

Motors

∙ Steel

∙ Steel / Stainless steel

∙ Aluminum

∙ Aluminum

∙ Copper

∙ Copper

∙ Plastics

∙ Brass

∙ Electronic components

∙ Magnetic materials

 

∙ Elektronic components

12.2 

Disposal

Return of products

Our products can be returned to us for disposal free of charge. However, this

requires that the products be free from oil, grease or other dirt.
Furthermore, the products returned for disposal may not contain any undue

foreign material or foreign components.
Deliver the products "free domicile" to the following address:

 

Bosch Rexroth AG

 

Electric Drives and Controls

 

Buergermeister-Dr.-Nebel-Straße 2

 

97816 Lohr am Main, Germany

Packaging

Packaging  materials  consist  of  cardboard,  wood  and  polystyrene  They  can

be recycled anywhere without any problem.
For ecological reasons, please refrain from returning the empty packages to

us.

Batteries and accumulators

Batteries and accumulators can be labeled with this symbol.

The  symbol  indicating  "separate  collection"  for  all  batteries  and

accumulators is the crossed-out wheeled bin.
End  users  in  the  EU  are  legally  bound  to  return  used  batteries  and

accumulators.  Outside  the  validity  of  the  EU  Directive  2006/66/EC,  the

particularly applicable regulations must be followed.
Batteries  and  accumulators  can  contain  hazardous  substances  which  can

harm the environment or people's health when improperly stored or disposed

of.
After use, the batteries or accumulators contained in Rexroth products must

be properly disposed of according to the country-specific collection systems.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03  

365/407

Environmental protection and disposal

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews: