Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 313

Page: 313 / 422

Accessories

10.1

Overview

KCU

KSM, KMS

●

HAS01

Basic accessory

●

HAS02

Shield connection of hybrid cable

●

HAS03

Control cabinet adapter

●

RKB0013

Short Multi-Ethernet cable for

connection to the neighboring device

●

netSWITCH sercos III

The accessory connects a sercos III

network into a standard Ethernet

network.

●

RBS0023

Connector for safety zone node

●

RKB0033

Cable with open ends

(X141 ↔ external safety unit)

●

RKB0043

Cable for communication

(M12‑D ↔ M12‑D)

●

RKB0044

Cable for communication

(M12‑D ↔ RJ-45)

●

RKS0010

Cable with open ends

(M12‑A ↔ open)

Fixing clip for hybrid cables
●

HAS10.1-001-001

For devices without optional

communication output

coupling (X108, X109).

●

HAS10.1-001-002

For devices with optional

communication output

coupling (X108, X109).

●

HAS05.1-021

Hybrid joint

●

HAS05.1-023

HCS01 adapter

●

HAS05.1-024

Passive 42 V supply unit

●

Metallic flange for circular connectors

Tab. 10-1:

Accessories

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

299/407

Accessories

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands