manualshive.com logo in svg

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual, Page: 129 / 422

Share
Download
Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 129

Description

Symbol

Unit

REH0800

Oil resistance

EN 60811-2-1 and EN 50363-10-2

Flammability

EN 60332-1-2; UL 758, Sec. 40, Cable Flame Test

Sec. 1061 according to UL 1581 and CSA C22.2 No.

210-05, Sec. 8.8.2

Latest amendment: 2019-06-17

1)

According to EN 50363-10-2

2) 3) 4)

Flexible cable track parameters: Maximum values only apply

individually

5)

UL file number according to cable marking

Tab. 5-19:

REH - Technical data

The  hybrid  cable  contains  both  power  lines  and  control  lines.

Route  hybrid  cables  in  accordance  with  EN  61800‑5‑1  and

EN  61800‑5‑2,  protected  against  external  damage.  Select  the

types  of  protective  measures  according  to  the  respective

application.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03  

115/407

Technical data of the components

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments