Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 190

Page: 190 / 422

X141, safety technology "Safe Motion" (S3, SD options)

Devices with safety technology "Safe Motion" cannot be operated

in a "Safe Torque Off" safety zone.
For any "mixed operation", drives with safety technology "Safe

Motion" in the drive line have to be connected behind the safety

zones. The RBS0023 safety zone connector should not be used.

View

Connecti

Signal name

Function

Female connector M12 (12‑pin,

D‑coded)

SI_In_Ch1

Input 1

SI_In_Ch2

Input 2

Zone_Br

X141.3 has to be accordingly controlled for the desired

function:
●

"Release brake":
Short circuit to X141.9
(input voltage: 24 V ±20%)

+24V

Power supply of the inputs and outputs

SI_In_Ch1_Zone Input 1 from preceding axis

0V_Zone

0 V from preceding axis

SI_In_Ch2_Zone Input 2 from preceding axis

SI_Out_Ch1

Safe output channel 1

24V_Br

Internal interface only;
24 V for "release brake" function

Power supply of the inputs and outputs

GND

GND for "zone detection" function

SI_Out_Ch2

Safe output channel 2

Ready-made connection cable

RKB0033

Can be used for processing of the inputs and controlling of the outputs.
Can be used for "releasing the brake".

Tab. 6-30:

Function, pin assignment, properties

Technical data

chapter 14.1.3 "Digital inputs (safety technology S options)" on page 370
chapter 14.2.2 "Digital outputs (safety technology S options)" on page 372

176/407

Connection points

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands