Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 384

Page: 384 / 422

14.1.3

Digital inputs (safety technology S options)

The digital inputs correspond to IEC 61131, type 1.

Data

Unit

min.

max.

Allowed input voltage

-3

High

Low

-3

Current consumption

Tab. 14-3:

Digital inputs (safety technology S options)

Time behavior

Description

Unit

min.

max.

Test pulse width (t

)

µs

1000

Percentage of High time (T

×100%)

100

Phase shift between two test pulses on both channels

(φ)

Tab. 14-4:

Time behavior

370/407

Appendix

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands