manualshive.com logo in svg

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual, Page: 364 / 422

Share
Download
Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 364

EtherCAT

LED: Color / flashing pattern

 1)

Significance

Description

Off

Status

INIT

●

Cyclic  process  data  and  acyclic  data

channel are not transmitted

●

No error

 

Flashing green

Status

PRE-OPERATIONAL

Acyclic data channel is transmitted

 

Green, lighting up once

Status

SAFE-OPERATIONAL

Acyclic data channel is transmitted

Permanently lit green

Status

OPERATIONAL

Cyclic  process  data  and  acyclic  data  channel

are transmitted

 

Flashing red

Configuration error

General EtherCAT configuration error

 

Red, lighting up once

Synchronization error

●

The  drive  controller  has  not  been

synchronized to the EtherCAT master

●

Communication  error  of  the  drive

controller

 

Red, lighting up twice

Timeout - watchdog

●

Timeout  while  cyclic  process  data  are

monitored

●

Watchdog of the EtherCAT master

1)

Flashing pattern: One square corresponds to a duration of

200 ms; the arrow marks the end of a cycle; abbreviations on

the squares: GN = LED permanently lit green, RD = LED per‐

manently lit red, -- = LED is off

Tab. 11-7:

Diagnostic LED

350/407

Commissioning, operation, diagnostics and maintenance

 IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments