Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 297

Page: 297 / 422

9.4

KCU02

9.4.1

Mounting depths

Adjusting Mounting Depths

HMV01 and HCS03 devices have greater mounting depths than the drive

connection box KCU. For connecting the drive connection box KCU to an

HMV01 or HCS03 device, you must therefore use the control cabinet adapter

HAS03.1-002

which compensates the different mounting depths.

9.4.2

Touch guard

Lethal electric shock by live parts with more

than 50 V!

WARNING

●

The appropriate touch guard must be mounted for each device following

connection work.
Never operate the device without mounted touch guard.

●

Never mount a damaged touch guard.

●

Immediately replace a damaged touch guard by an undamaged touch

guard.

●

Keep the cutouts at the touch guard as small as possible. Only remove

the cutouts if necessary.

Cutouts at the touch guard

●

If the DC bus and the control voltage are connected via contact bars, only

cutout A may be removed from the touch guard.

●

If the DC bus and the control voltage are connected via cables (e.g., in the case

of multiple-line arrangement), cutouts A, B and C may be removed from the

touch guard.

●

At the first and last device in a line of interconnected devices, cutouts may not

be removed from the outer side of the touch guard.

Tab. 9-3:

Cutouts at the touch guard

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

283/407

Mounting and installation

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands