Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 302

Page: 302 / 422

9.6.3

Electrical interfaces

Overall connection diagram

At the first KSM/KMS, always plug the hybrid cable RKH in

connection point X103.1.
Always terminate the unassigned X103.x connections at

KSM/KMS/KMV with an RHS terminal connector so that the

degree of protection IP65 is maintained.

The figures below show examples. Other mains connection options are

described in the documentation "Rexroth IndraDrive Drive Systems with

HMV01/02, HMS01/02, HMD01, HCS02/03".
The additional components (DST, HNL, HNF …) contained in the figure are

not absolutely necessary. As regards the detailed configuration of a drive

system, see documentation "Rexroth IndraDrive Drive Systems with

HMV01/02, HMS01/02, HMD01, HCS02/03".

288/407

Mounting and installation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands