manualshive.com logo in svg

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

The Bosch Rexroth IndraDrive Mi KCU02 is a state-of-the-art industrial drive controller. Unlock its full potential with the comprehensive Instruction Manual, available for free download on our website. This manual provides detailed guidance and insights to ensure smooth operation and maximum efficiency. Get yours now at manualshive.com!

Share
Download
background image

1.2 

IndraDrive Mi drive system

1.2.1 

Components

KCU02 drive connection box

The KCU02 drive connection box
●

supplies  the  KSM  motor-integrated  servo  drives  and  the  KMS  near

motor servo drives
–

with power (from the DC bus connection to an HMV supply unit or

HCS converter)

–

with 42V control voltage

●

with  integrated  fuses  protects  the  RKH  hybrid  cable  against  electric

overload

●

allows the higher-level control unit to communicate with the KSM motor-

integrated servo drives and KMS near motor servo drives

⇒ 

chapter "KSM02 motor-integrated servo drive" on page 2

⇒ 

chapter "KMS02 near motor servo drive" on page 3

 

KMV03 supply unit

The KMV03 supply unit
●

supplies  the  KSM  motor-integrated  servo  drives  and  KMS  near  motor

servo drives
–

with power

–

with 42V control voltage

●

allows the higher-level control unit to communicate with the KSM motor-

integrated servo drives and KMS near motor servo drives

⇒ 

chapter "KNK03 mains filter, KMV03 supply unit, KLC03 DC bus capacitor

unit, KMS03 near motor servo drive" on page 4

.

 

KNK03 mains filter

Mains filters reduce radio interference and mains pollution.
⇒ 

chapter "KNK03 mains filter, KMV03 supply unit, KLC03 DC bus capacitor

unit, KMS03 near motor servo drive" on page 4

.

 

KLC03 DC bus capacitor unit

DC bus capacitor units buffer energy in the DC bus of the drive system.
⇒ 

chapter "KNK03 mains filter, KMV03 supply unit, KLC03 DC bus capacitor

unit, KMS03 near motor servo drive" on page 4

.

 

KSM motor-integrated servo drive

The KSM motor-integrated servo drive consists of:
●

Servo motor (on the basis of Rexroth IndraDyn S)

●

Drive electronics, consisting of control section and power section

⇒ 

chapter "KSM02 motor-integrated servo drive" on page 2

 

KMS near motor servo drive

The  KMS  near  motor  servo  drive  consists  of  control  section  and  power

section.
⇒ 

chapter "KMS02 near motor servo drive" on page 3

 
 

RKH hybrid cable

The RKH hybrid cable replaces the following individual cables:

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03  

7/407

System presentation

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Rexroth IndraDrive Mi KCU02

Balboa Instruments EL Series Hot Sheet preview
EL Series
Brand: Balboa Instruments Pages: 10
Quantum Data 980 Application Manual preview
980
Brand: Quantum Data Pages: 36
Access Flow2 User'S Manual & Installation Instructions preview
Flow2
Brand: Access Pages: 12
Samson 3430 Operating Instructions Manual preview
3430
Brand: Samson Pages: 52
Samson 3275 Mounting And Operating Instructions preview
3275
Brand: Samson Pages: 32
Danfoss Cascade Operating Instructions Manual preview
Cascade
Brand: Danfoss Pages: 59
Hanna Instruments BL120 Instruction Manual preview
BL120
Brand: Hanna Instruments Pages: 54
Hanna Instruments BL 983320-0 Instruction Manual preview
BL 983320-0
Brand: Hanna Instruments Pages: 2
ICP DAS USA I-7000 Series Quick Start Manual preview
I-7000 Series
Brand: ICP DAS USA Pages: 6
Veeder-Root TLS Install, Setup, & Operation Manual preview
TLS
Brand: Veeder-Root Pages: 27
Valve Concepts 1078 Installation, Operation And Maintenance Manual preview
1078
Brand: Valve Concepts Pages: 18
K&K M1500 Installation Instructions Manual preview
M1500
Brand: K&K Pages: 6
Magnescale LY71 Manual preview
LY71
Brand: Magnescale Pages: 3
S.R.Smith PAL Instructions preview
PAL
Brand: S.R.Smith Pages: 2
Watts AMES 4000SS Series Installation And Repair Manual preview
AMES 4000SS Series
Brand: Watts Pages: 8
CIAT CIATControl OPC Server Installation And Operating Instructions Manual preview
CIATControl OPC Server
Brand: CIAT Pages: 32
Challenger Lifts EnviroLift EW0820S090 Installation, Operation & Maintenance Manual preview
EnviroLift EW0820S090
Brand: Challenger Lifts Pages: 23
Danfoss AFD 2 VFG 2 Operating Manual preview
AFD 2 VFG 2
Brand: Danfoss Pages: 8

Brands by name

Popular brands

Load more brands