Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 369

Page: 369 / 422

●

E3 (X38.4): +24 V to activate drive enable

See Functional Description of firmware → "Easy startup mode".

Analog outputs

KSM/KMS have no analog outputs!

Oscilloscope function

It is possible to use the oscilloscope function integrated in the drive and

described in the Functional Description of the firmware!

See Functional Description of firmware → "Oscilloscope function".

Patch function

With the patch function you can read or write controller-internal memory cells.

See Functional Description of firmware → "Patch function".

Monitoring function

The monitoring function provides extended diagnostic possibilities.

See Functional Description of firmware → "Monitoring function".

Logbook function

With the logbook function you can reproduce the internal firmware sequence.

See Functional Description of firmware → "Logbook function".

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

355/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands