manualshive.com logo in svg

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual, Page: 303 / 422

Share
Download
Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 303

HMV01 used as supply unit

IndraDrive Mi drive system with HMV01 supply unit:

24V

24V supply

DST

Transformer (optional)

F

Fuses

HMD, HMS Inverter (optional)

HMV01

Supply unit

HNF

Mains filter

HNL

Mains choke

K1

Mains contactor (only for supply units without integrated mains

contactor, e.g. HMV01.1R-W0120)

KCU

Drive connection box

KSM

Motor-integrated servo drive

MSK

Servo motor (optional)

RHS

Terminal connector

RKB

Communication cable

RKG

Encoder cable (optional)

RKH

Hybrid cable

RKL

Motor cable (optional)

X14

Mains synchronization (only with regenerative HMVs)

X103.1

Connection of RKH hybrid cable at first KSM

Fig. 9-4:

IndraDrive Mi drive system with HMV01

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03  

289/407

Mounting and installation

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments